Philio
Smart Energy In Wall Meter
SKU: PAB01-1
Quickstart
This is a
1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer. 2. Pressing Include button three times within 2 seconds will enter inclusion mode.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
This dual meter module is a transceiver which is a Z-WaveTM enabled device and is fully compatible with any Z-WaveTM enabled network. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. And it can act as repeaters within the network regardless of vendor to increase reliability of the network.Mini size design let the module can easily hide itself into the electricity distribution box and that will be good for the house decoration. This dual meter module is able to detect Instant power wattage (13800W/230Vac)(60 Amperes) of connected light or appliances.
| Reset to factory default | Use this procedure only in the event that the primary controller is lost or otherwise inoperable.1. Pressing INCLUDE_BUTTON three times within 2 seconds will enter inclusion mode.2. Within 1 second, press Include button again for 5 seconds. 3. IDs are excluded. |
| Inclusion | 1. Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer. 2. Pressing Include button three times within 2 seconds will enter inclusion mode. |
| Exclusion | 1. Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer. 2. Pressing Include button three times within 2 seconds will enter exclusion mode. 3. Node ID has been excluded. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus LifelineFor group 1, the Switch will report (1) Instant Power Consumption (Watt) read from CT1 (2) Accumulated Power Consumption (KWh) read from CT1. |
| 2 | 1 | For group 2, the Switch will report (1) Instant Power Consumption (Watt) read from CT2 (2) Accumulated Power Consumption (KWh) read from CT2. |
| 3 | 1 | For group 3, the Switch will report (1) The sum of instant Power Consumption (Watt) read from CT1 and CT2 (2) The sum of accumulated Power Consumption (KWh) read from CT1 and CT2. |
Configuration Parameters
Parameter 1: Watt Meter Report Period
If the setting is configured for 1hour (set value =720), the PAB01 will report its instant power consumption every 1 hour to the node of correspond Group. The maximum interval to report its instant power consumption is 45 hours (5s*32767/3600=45hr). Size: 2 Byte, Default Value: 720
| Setting | Description |
|---|---|
| 1 - 32767 | 5*720s=3600s=1 hour |
Parameter 2: KWH Meter Report Period
If the setting is configured for 1hour (set value =720), the PAB01 will report its Accumulated Power Consumption (KW/h) every 1 hour to the node of correspond Group. The maximum interval to report its Accumulated Power Consumption (KW/h) is 45 hours (5s*32767/3600=45hr). Size: 2 Byte, Default Value: 720
| Setting | Description |
|---|---|
| 1 - 32767 | 5*720s=3600s=1 hour |
Parameter 3: Selected Endpoint
If Controller can't use Multi_Channel command class to access the endpoint of PAB01, you may configure the endpoint value to react the Basic Command Class Binary Switch Command Class or Meter Command Class V3. Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 | 1CT1 |
| 2 | 2CT2 |
| 3 | 3CT1 and CT2 |
Parameter 4: Threshold of Current for Load Caution
This is a warning when the current of load over the preset threshold value, If the setting value is 6000, when the load wattage of CT1 or CT2 over 60A, PAB01 will send current Meter Report command to the node of correspond Group. Size: 2 Byte, Default Value: 6000
| Setting | Description |
|---|---|
| 10 - 6000 | 6000*0.01A=60A |
Parameter 5: Threshold of KWh for Load Caution
This is a warning when the KWh of load over the preset threshold value, If the setting value is 10000, when the Accumulated Power Consumption of CT1 or CT2 over this value, PAB01 will send KWh Meter Report command to the node of correspond Guoup, minum value is 1KWh and default value is 10000 kWh. Size: 2 Byte, Default Value: 10000
| Setting | Description |
|---|---|
| 1 - 10000 | 10000*1KWH=10000KWH |
Parameter 6: Existence of Endpoint3
Multi-Channel Command is a good way to control relay1 and relay2 of PAB01 individually. The endpoint3 of PAB01 is related to both relay1 and relay2. In some condition it becomes redundant in Multi-Channel Command Class. When the Existence of Endpoint3 is set as 2, the endpoint3 will be disabled. The default value is 1. Endpoint1 and Endpoint2 are fixed, only Endpoint3 is dynamic. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | 1 : Endpoint3 exist |
| 2 | 2 : No Endpoint3 |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | Whole Home Meter - Simple |
| Network Operation | Always On Slave |
| Firmware Version | 01 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-16010004 |
| Z-Wave Product Id | 0x013C.0x0006.0x001A |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |