GATEMAN
A200-CH
SKU: GDM-M2D6D-K0
Quickstart
This is a
To include:1. Touch keypad with palm2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)3. Press 'R' button [Registration] from the inside of battery cover.4. Press 9,#,1,# on the keypad (by sequence)5. Wait until 'Ding dong dang' melody play than press 'R' button [Registration]
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
A mortise type digital door lock for smart home services.'A200-CH' is a security enabled Z-Wave Plus product for Korean domestic market. It can be included and operated in any Z-Wave network with other Z-Wave certified devices.
| Reset to factory default | To reset to factory defaults:Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. (User code or master code remains the same. Only network settings reset to factory defaults.) 1. Touch keypad with palm2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)3. Press 'R' button [Registration] from the inside of battery cover.4. Press 9,#,9,# on the keypad (by sequence)5. Wait until 'Ding dong dang' melody play than press 'R' button [Registration] |
| Inclusion | To include:1. Touch keypad with palm2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)3. Press 'R' button [Registration] from the inside of battery cover.4. Press 9,#,1,# on the keypad (by sequence)5. Wait until 'Ding dong dang' melody play than press 'R' button [Registration] |
| Exclusion | To exclude:1. Touch keypad with palm2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)3. Press 'R' button [Registration] from the inside of battery cover.4. Press 9,#,3,# on the keypad (by sequence)5. Wait until 'Ding dong dang' melody play than press 'R' button [Registration] |
| NIF | XXXNIF |
| Wakeup | The lock is always in 'Wake up status'.However, touch with palm to begin and end action. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 1: Silent mode on/off
Set the silent mode on/off Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 3 | unsigned value |
Parameter 2: Auto relock on/off
Set the auto relock on/off Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 255 | unsigned value |
Parameter 3: relock time
Set the relock time Size: 1 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 10 - 180 | unsigned value |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Door Lock Keypad |
| Network Operation | Listening Sleeping Slave |
| Firmware Version | HW: 16.16.16.16.16 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-16065106 |
| Z-Wave Product Id | 0x0212.0xC600.0x0004 |
| Door Lock Type | Lever Handle |
| Firmware Updatable | Updatable by Manufacturer |
| Color | Silver |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |