Quickstart
This is a
Light Dimmer Switch for XXXQFrequencyName.
To run this device please connect it to your mains power supply.
To add this device to your network execute the following action:
1. Bring your Z-Wave gateway hub or controller as close to the switch as possible2. Put your Z-Wave controller in inclusion mode3. Tap the switch on and off quickly 3 times to finalize the inclusion process4. A new dimming device should appear on your controller's device listTroubleshooting Tips:If you are unable to include the Z-Wave dimmer to your controller, please try one of the following:- Bring the controller closer to your Z-Wave switch or use a hand-held secondary controller for inclusion- Tap your Z-Wave switch quicker 4 or 5 times once you put the controller in the inclusion mode to ensure the command has gone through- Put your controller in the EXCLUSION mode and tap the switch quickly 3 times, then try adding it to your network again
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
PRODUCT FEATURES:- Manual or remote on/off control and dimming from your mobile device or computer (when included to a Z-Wave gateway controller)- Z-Wave Plus with improved 500 chip for faster and safer wireless communication- Works with most high-quality DIMMABLE LED, CFL, and incandescent bulbs- Based on universal command classes - supported by most Z-Wave controllers- May be associated and grouped with other Z-Wave devices for advanced home automation- LED indicator to help locate the switch in dark space- Simple elegant design with screwless snap-on wall plate included- Built-in Z-Wave signal repeater for a stronger and more reliable networkSPECIFICATIONS:Model Number: ZEN22Z-Wave Signal Frequency: 908.42 MHzPower: 120 VAC, 60 HzMaximum Loads: 500W Single-gang, 400W Double-gang, 300W Triple-gang Incandescent, 150W CFL or LEDRange: Up to 100 feet line of sightOperating Temperature: 32-104 F (0-40 C)Installation and Use: Indoor only
| Reset to factory default |
The switch will be reset to factory defaults only by exclusion using a Z-Wave controller. You may use any certified Z-Wave controller to exclude and reset the switch. This device may not be reset manually when the networks primary controller is missing or otherwise inoperable. NOTE: All previously recorded activity and custom settings will be erased from the devices memory. |
| Inclusion |
1. Bring your Z-Wave gateway hub or controller as close to the switch as possible2. Put your Z-Wave controller in inclusion mode3. Tap the switch on and off quickly 3 times to finalize the inclusion process4. A new dimming device should appear on your controller's device listTroubleshooting Tips:If you are unable to include the Z-Wave dimmer to your controller, please try one of the following:- Bring the controller closer to your Z-Wave switch or use a hand-held secondary controller for inclusion- Tap your Z-Wave switch quicker 4 or 5 times once you put the controller in the inclusion mode to ensure the command has gone through- Put your controller in the EXCLUSION mode and tap the switch quickly 3 times, then try adding it to your network again |
| Exclusion |
1. Bring your Z-Wave gateway hub or controller as close to the switch as possible2. Put your Z-Wave controller in exclusion mode3. Tap the switch on and off quickly 3 times to complete the exclusion process4. The device should disappear from your controller's device list |
| NIF |
XXXNIF |
| Wakeup |
XXXWakeupDescription |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
5 |
Depending on your Z-Wave gateway's home automation software capabilities, you may be able to associate your Z-Wave switch in groups with other Z-Wave devices to schedule scenes and create events. This dimmer switch supports Group 1 with up to five devices for lifeline communication. This device will send SWTICH MULTILEVEL REPORT to Group 1 when operated manually.Please refer to your controller's user guide for advanced programming instructions as they are a little different for every software. |
Technical Data
| Hardware Platform |
ZM5202 |
| Device Type |
Light Dimmer Switch |
| Network Operation |
Always On Slave |
| Firmware Version |
HW: 1 FW: 20.15 |
| Z-Wave Version |
6.51.06 |
| Certification ID |
ZC10-16085194 |
| Z-Wave Product Id |
0x015D.0x0112.0x241C |
| Color |
White |
| Neutral Wire Required |
ok |
| Switch Type |
Decorator Paddle Push with Indicator |
| Electric Load Type |
Dimmable LEDIncandescent |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
