This is a
Leviton Decora Smart Z-Wave devices support two methods of inclusion. When using a Z-Wave Plus certified controller choose Network Wide Inclusion.Network Wide Inclusion:Network Wide Inclusion allows your device to be included into the network using devices already in the network to assist with communication. Work your way from the closest devices to the controller outward. Enter Programming Mode by holding the top of the paddle for 7 seconds, the Locator LED will blink amber. Tap the top of the paddle one time.The Locator LED will quickly flash green. The Decora Smart Z-Wave device is ready to learn into the Z-Wave network. Follow directions in the Z-Wave controller to complete the adding process. Upon successful addition to network the LED will turn off and then blink green 3 times. If the adding process is not successful the LED will flash red 3 times.Traditional Inclusion:For older controllers Traditional Inclusion is supported. Depending on the age of the controller the controller will need to be 3 to 35 feet from the device when including. Enter Programming Mode by holding the top of the paddle for 7 seconds, the Locator LED will blink amber. The Decora SmartTM Z-Wave device is ready to add to the Z-Wave network. Follow directions in the Z-Wave controller to enter learn mode. Tap the top of the paddle one time. The Locator LED will quickly flash green. The Z-Wave controller will begin to pair with the Decora Smart device. Upon successful addition to the network the LED will turn off and then blink green 3 times. If the adding process is not successful the LED will flash red 3 times.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
The wireless Leviton DZ1KD is a Z-Wave enabled dimmer designed for use for most residential lighting applications to control LED, CFL, and incandescent bulbs. The DZ1KD Dimmer is fully compatible with Z-Wave Plus certified controllers. Provides full range dimming with adjustable fade rates.Manufacturer Parameters allow custom configuration via Z-Wave commands. Offers manual control to turn lights on/off and set brightness level, with an LED feedback to display brightness level.Facilitates single pole or three-way multi-location applications.Rated for 450W LED and CFL dimmable bulbs and 1000W incandescent bulbs, requires neutral connection.These Z-Wave Plus devices support beaming, network wide inclusion, and over the air updates.White and Light Almond color faces included, Decora wallplate sold separately.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
When removing a device from a network it is best practice to use the Exclusion process. In situations where a device needs to be returned to factory default follow the following steps. A reset should only be used when a controller is inoperable or missing. Hold the top of the paddle for a total of 14 seconds. After the first 7 seconds the LED turns amber. The Locator LED will quickly flash red/amber after 14 seconds. Release the top of the paddle and the device will reset.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave PlusTM Lifeline: A NOTIFICATION frame is sent to the nodesin this association group when a Lifeline event occurs. All nodes in the association group |
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Fade On Time Parameter No: 1, Length: 1 Byte Valid Values = 0 to 253 (default 2)- 0 = Instant On- 1 - 127 = Seconds: 1 - 127 seconds- 128 - 253 (0x80 - 0xFD) = Minutes: 1 - 126 minutes Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
128 - 253 | 1-126 Minutes |
0 - 253 | Valid Values |
0 | Instant On |
1 - 127 | 1-127 Seconds |
Fade Off Time Parameter No: 2, Length: 1 Byte Valid Values = 0 to 253 (default 2)- 0 = Instant Off- 1 - 127 = Seconds: 1 - 127 seconds- 128 - 253 (0x80 - 0xFD) = Minutes: 1 - 126 minutes Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
128 - 253 | 1-126 Minutes |
0 - 253 | Valid Values |
0 | Instant Off |
1 - 127 | 1-127 Seconds |
Minimum Light Level Parameter No: 3, Length: 1 Byte Valid Values = 0 to 100 (default 10) Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
0 - 100 | Valid Values |
Maximum Light Level Parameter No: 4, Length: 1 Byte Valid Values = 0 to 100 (default 100) Size: 1 Byte, Default Value: 100
Setting | Description |
---|---|
0 - 100 | Valid Values |
Preset Light Level Parameter No: 5, Length: 1 Byte Valid Values = 0 to 100 (default 0)- 0 = Memory Dim - Last dim state- 1 - 100 = Level Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Memory Dim (Last Dim State) |
1 - 100 | Level |
0 - 100 | Valid Values |
LED Dim Level Indicator Timeout Parameter No: 6, Length: 1 Byte Valid Values = 0 to 255 (0xFF) (default 3)- 0 = Level Indicators Off- 1 - 254 (0x01 - 0xFE) = Level Indicator Timeout (seconds)- 255 (0xFF) = Levels Always On Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
0 | Level Indicators Off |
1 - 254 | Level Indicator Timeout (seconds) |
255 | Indicators Always On |
0 - 255 | Valid Values |
Locator LED Status Parameter No: 7, Length: 1 Byte Valid Values = 0 to 255 (0xFF) (default 255 (0xFF))- 0 = LED Off- 254 (0xFE) = Status Mode- 255 (0xFF) = Locator Mode Size: 1 Byte, Default Value: 255
Setting | Description |
---|---|
0 | LED Off |
254 | LED Status Mode (0xFE) |
255 | LED Locator Mode (0xFF) |
Load Type Parameter No: 8, Length: 1 Byte Valid Values = 0 to 3 (default 0)- 0 = Incandescent- 1 = LED- 2 = CFL- 3 = Mark 10 Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 3 | Load Type |
Hardware Platform | ZM5202 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 255 FW: 1.22 |
Z-Wave Version | 6.61.00 |
Certification ID | ZC10-16095222 |
Z-Wave Product Id | 0x001D.0x3301.0x0001 |
Z-Wave Scene Type | Scene |
Switch Type | Decorator Paddle Push with Indicator |
Neutral Wire Required | ok |
Firmware Updatable | Updatable by Consumer by RF |
Electric Load Type | Dimmable LEDIncandescentInductive (e.g. Motor)LEDMLV (Magnetic) |
Color | White |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |