Aeotec

LED Strip

SKU: ZW121-A


Quickstart

This is a Light Dimmer Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
Turn the primary controller of Z-Wave network into inclusion mode, press the Action Button on the LED Strip Controller.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

Aeotec LED Strip is a multi-coloured LED Strip which allows control (on/off/dim/colour change) via wireless Z-Wave commands. The LED Strip can also communicate securely via AES 128 wireless Z-Wave commands and supports Over-The-Air (OTA) firmware upgrades.
Reset to factory default Press and hold the Action Button on the LED Strip Controller for 20 seconds and then release it.Use this procedure only in the event that your primary network controller is missing or inoperable.
Inclusion Turn the primary controller of Z-Wave network into inclusion mode, press the Action Button on the LED Strip Controller.
Exclusion Turn the primary controller of Z-Wave network into exclusion mode, press the Action Button on the LED Strip Controller.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 The association group 1 is the Z-Wave Lifeline group. The Hail CC and Basic Report CC (configurable) can be sent to the associated nodes in association group 1.
2 5 In this group, the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands would be sent to the associated nodes in association group 2 when the LED Strip receives the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands from the main controller.

Configuration Parameters

Parameter 112: Set the Dimmer mode.

Set the Dimmer mode.
Size: 1 Byte, Default Value: 0

Setting Description
0 Parabolic curve mode
1 Index curve mode
2 (Parabolic + Index)/2 mode
3 Linear mode

Parameter 20: Set the LED Strips state after it is re-powered on

Set the LED Strips state after it is re-powered on.
Size: 1 Byte, Default Value: 1

Setting Description
1 Always On.
2 Always Off.
0 The last state before re-power on.

Parameter 252: Enable/disable Lock Configuration

Enable/disable to lock Configuration parameters.
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable
1 Enable

Parameter 255: Reset the LED Strip

Reset the LED Strip to factory default.
Size: 4 Byte, Default Value: 0

Setting Description
0 Reset all configuration parameters to factory default settings
1431655765 Reset the LED Strip to factory default.

Parameter 32: Enable/disable to send out a report when the color is changed.

Enable/disable to send out a report when the color is changed.
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable
1 Hail CC

Parameter 33: Get the LED strips color value.

Get the Bulbs color value.Note: This parameter is a get-only parameter.
Size: 4 Byte, Default Value: 0

Setting Description
256 - 65535 Green color value
1 - 255 Bule color value
65536 - 16777215 Red color value

Parameter 34: Enable/disable to turn on the last brightness level of the LED Strip when using the Color Switch Set CC to change its color.

Enable/disable to turn on the last brightness level of the LED Strip when using the Color Switch Set CC to change its color.
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable
1 Enable

Parameter 35: Configure the display mode of Cold/Warm white.

Configure the display mode of Cold/Warm white.
Size: 1 Byte, Default Value: 1

Setting Description
1 Complementary combination of Cold/Warm white.
0 Arbitrary combination of Cold/Warm white.

Parameter 36: Reboot/save/exit Colorful mode.

Reboot/save/exit Colorful mode.Note: This parameter is a set-only parameter.
Size: 1 Byte, Default Value: 0

Setting Description
0 Un-reboot Colorful mode.
1 Reboot Colorful mode.
2 Exit Colorful mode.
3 Save the current Colorful mode value and then to be exited.

Parameter 37: Colorful mode configuration.

Configure the Colorful mode.
Size: 4 Byte, Default Value: 157483008

Setting Description
0 - 31 Colour Change Speed Level
32 - 255 Time Base of Color Change Speed
256 - 65535 Cycle Count
65536 - 16777215 Brightness
16777215 - 134217727 Color Display Cycle
134217728 - 1073741823 Color Change Speed Option
1073741824 - 2147483647 Color Transition Style

Parameter 38: Change speed

Set the Change speed.
Size: 4 Byte, Default Value: 50332416

Setting Description
1 - 255 Set the pause time of OFF.
256 - 65535 Set the pause time of ON.
65536 - 16777215 Set the speed from ON to OFF.
16777216 - 2147483647 Set the speed from OFF to ON.

Parameter 39: Color index configuration when the LED Strip is in Multi color mode.

Color index configuration when the LED Strip is in Multi color mode.
Size: 4 Byte, Default Value: 2003125025

Setting Description
1 - 15 Index 8
16 - 255 Index 7
256 - 4095 Index 6
4096 - 65535 Index 5
65536 - 1048575 Index 4
1048576 - 16777215 Index 3
16777216 - 268435455 Index 2
268435456 - 2147483647 Index 1

Parameter 40: Colorful mode configuration.

Colorful mode configuration.
Size: 1 Byte, Default Value: 0

Setting Description
1 Rainbow mode.
2 Mutil color mode.
3 Fade out and fade in (Red).
4 Fade out and fade in (Green).
5 Fade out and fade in (Blue).

Parameter 80: To set whcih notification can be sent to the associated devices (Group 1) when the state of LED Bulb is changed.

To set whcih notification can be sent to the associated devices (Group 1) when the state of LED Bulb is changed.
Size: 1 Byte, Default Value: 1

Setting Description
3 Haill CC when pressing the Action Button to change its state
0 Nothing
1 Hail CC
2 Basic CC report.

Technical Data

Hardware Platform ZM5101
Device Type Light Dimmer Switch
Network Operation Always On Slave
Firmware Version HW: 121 FW: 1.00
Z-Wave Version 6.51.08
Certification ID ZC10-16095247
Z-Wave Product Id 0x0086.0x0103.0x0079
Switch Type Push Button Illuminated
Z-Wave Scene Type Scene
Color White
Firmware Updatable Updatable by Consumer by RF
Frequency XXfrequency
Maximum transmission power XXantenna
U.S. / Canada / MexicoLight Dimmer Switch