Sercomm
SW-ESW01N
SKU: SW-ESW01N
Quickstart
This is a
1.Put the Z-Wave controller into "Add (Inclusion)" mode.2.Power on the device.3.The LED is blinking while scanning the network and. This process may take up to 30 seconds. (In the meanwhile, our device will send its NIF.)4.If the add process is successful, the LED will turn off and restore to relay state.If the process failed, press the On/Off button once and the device will be in auto add mode again.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
SW-ESW01N is an electrical power measuring device, which is compatible with Z-Wave enabled devices with its embedded radio frequency (RF) technology. It can also be used with other devices with the Z-Wave logo regardless of the manufacturer.Furthermore, SW-ESW01N can act as a signal repeater that will extend the wireless transmission range and increase the reliability of your network. With a Z-Wave compatible gateway and software program, youll be able to monitor and inform the energy usage of the connected appliance.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
1.Press the On/Off button 4 times within two seconds and hold the 4th press until the LED lights up. 2.The LED will turn off after three seconds. The node ID will be cleared and all settings will be reset to factory defaults.3.The device will be in auto add mode.Note 1 :Relay state default offNote 2: Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
1.Put the Z-Wave controller into "Add (Inclusion)" mode.2.Power on the device.3.The LED is blinking while scanning the network and. This process may take up to 30 seconds. (In the meanwhile, our device will send its NIF.)4.If the add process is successful, the LED will turn off and restore to relay state.If the process failed, press the On/Off button once and the device will be in auto add mode again.Exclusion
1.Set the Z-Wave controller to "Remove (Exclusion)" mode.2.Press the On/Offbutton three times within two seconds.3.The LED will be blinking for one second. (In the meanwhile, our device will send its NIF.)Note 1: if the Remove process is successful, the node ID will be cleared and the device will be in auto add mode.Note 2:Relay state default offCommunication to a Sleeping device (Wakeup)
This device is battery operated and turned into deep sleep state most of the time to save battery life time. Communication with the device is limited. In order to communicate with the device, a static controller C is needed in the network. This controller will maintain a mailbox for the battery operated devices and store commands that can not be received during deep sleep state. Without such a controller, communication may become impossible and/or the battery life time is significantly decreased.
This device will wakeup regularly and announce the wakeup state by sending out a so called Wakeup Notification. The controller can then empty the mailbox. Therefore, the device needs to be configured with the desired wakeup interval and the node ID of the controller. If the device was included by a static controller this controller will usually perform all necessary configurations. The wakeup interval is a tradeoff between maximal battery life time and the desired responses of the device. To wakeup the device please perform the following action: Not battery powered
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Support grouping identifier = 1 Support one group with 5 nodes. All triggering report will be sent to the associated nodes. |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: Relay state when power up
Relay state when power up0 : Last relay state (default setting)1 : Relay on2 : Relay off Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 2 | Relay state when power up |
Parameter 2: Auto report relay state
Auto report relay state0 : Disable1 : Enable (default setting) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | Auto report relay state |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 3 FW: 2.01 |
| Z-Wave Version | 6.51.07 |
| Certification ID | ZC10-17015384 |
| Z-Wave Product Id | 0x0151.0x0201.0x0001 |
| Supported Meter Type | Electric Energy |
| Color | White |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info
- Association V2
- Basic
- Configuration
- Device Reset Locally
- Firmware Update Md V2
- Manufacturer Specific V2
- Meter V3
- Notification V4
- Powerlevel
- Switch Binary
- Version V2
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.