This is a
Initiate the process to add the lock to your system at your smart home controller.When prompted by your smart home system to add the lock, press button A on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.Please allow time for the controller to add the lock to your system.
Kwikset, the leader in residential security, introduces the SmartCode 910 Touchpad Electronic Deadbolt with Z-Wave.Backlit keypad with One touch locking30 user codesBHMA grade 2 certifiedFull 128-bit encryption securityDrill and pick resistant backup keywaySmartKey: Re-key the lock in seconds
Reset to factory default | A factory reset will delete all user codes associated with the lock and will remove itself from your smart home system.Please only perform a factory reset when the primary controller is missing or inoperable.To perform a factory reset, please perform the following:1. Remove the battery pack2. Press and HOLD the Program button while reinserting the battery pack.3. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.4. Press the Program button once more.The status LED will flash green and red several times.5. After a few seconds, the lock will initiate the door handing process. |
Inclusion | Initiate the process to add the lock to your system at your smart home controller.When prompted by your smart home system to add the lock, press button A on the lock interior one time. The red LED will illuminate when the lock enters Add Mode.Please allow time for the controller to add the lock to your system. |
Exclusion | Follow your smart home systems instructions to remove the lock from the network. When prompted by the system, press button A on the lock interior once.The red LED will illuminate when the lock enters Remove mode. |
NIF | XXXNIF |
Wakeup | Even though the lock is sleeping, all buttons are active and can be used to initiate any lock activity.For the RF side, it will wake up every 1 second to check if there are any requests from your smart home controller. |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Z-Wave Plus LifelineSupports the following types of unsolicited messages:Battery Report - sends periodic battery reports containing the battery percentage.Door Lock Operation Report - upon power up, this message will be sent to allow the controller to sync up with the current lock status.Notification Report - many notification types will be sent for status and alarms.The following notification types are supported:Access Control (V2), Home Security (V2), and Power Management (V2).Device Reset Locally Notification - this message will be sent to notify the smart home controller that the lock is resetting back to factory defaults and will be leaving the network. |
2 | 5 | This group will provide all Notification reports as described for the Lifeline.This group allows other controllers, other than the lifeline, to receive these types of unsolicited messages as well. |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 1. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 10. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 11. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 12. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 13. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 14. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 15. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 16. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 17. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 18. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 19. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 2. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 20. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 21. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 22. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 23. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 24. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 25. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 26. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 27. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 28. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 29. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 3. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 30. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This is a one byte read only bit mask that returns the state of the user accessible dipswitches on the rear panel of the door lock.0x01: Lock Status LED (1: enabled, 0: disabled)0x02: Autolock setting (1: enabled, 0: disabled)0x04: Buzzer (1: enabled, 0: disabled) Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
0 | All features disabled |
1 | Lock Status LED enabled |
2 | Autolock enabled |
4 | Internal Buzzer enabled |
3 | Autolock & Lock status LED enabled |
5 | Internal buzzer & Lock status LED enabled |
7 | All features enabled |
This configuration parameter provides the first 4 bytes of the SKU number that has been programmed into the lock.Each byte allows all printable characters from 32 to 126. Size: 4 Byte, Default Value: 32
Setting | Description |
---|---|
32 - 126 | All printable characters |
This configuration parameter provides the second and last 4 bytes of the SKU number that has been programmed into the lock.Each byte allows all printable characters from 32 to 126. Size: 4 Byte, Default Value: 32
Setting | Description |
---|---|
32 - 126 | All printable characters |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 4. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter allows the smart home controller to force a factory reset of the lock.After receiving this request, the lock will send a Device Reset Locally message back to the lifeline controller. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | No action taken |
1 | Force Factory Reset |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 5. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 6. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 7. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 8. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
This configuration parameter is used to get or set the type of user for their corresponding user code. By default, all user codes are set to the Owner type unless otherwise specified. The parameter type is associated with the user code location 9. Caution must be used when setting these values. Guests and Workers will require schedules attached to them in order for those types to be assigned. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Owner |
3 | Guest |
4 | Worker |
Hardware Platform | ZM5101 |
Device Type | Door Lock - Keypad |
Network Operation | Listening Sleeping Slave |
Firmware Version | HW: 2 FW: 4.08:56.11 |
Z-Wave Version | 6.51.08 |
Certification ID | ZC10-17025453 |
Z-Wave Product Id | 0x0090.0x0003.0x0238 |
Communications Protocol | Z-Wave Serial API |
Firmware Updatable | Updatable by Consumer by RF |
Door Lock Type | Deadbolt |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |