Quickstart
This is a
secure
Light Dimmer Switch for XXXQFrequencyName.
To run this device please connect it to your mains power supply.
To add this device to your network execute the following action:
1. Screw the RGBW bulb into a standard E27 socket.2. Turn on the bulb with your wall switch to apply power to the bulb. a) If youre not using a wall switch, then use your alternate method to apply power to the bulb.3. Activate the included/excluded mode on your Z-wave controller or gateway.a) This may also be done through your associated app, if your ecosystem has that capability.4. Toggle the wall-switch, from OFF, then to ON. a) Or use your alternate method to toggle power from OFF, then to ON. 5. The LED bulb will flash once if it has been successfully included/ excluded into your Z-Wave network.Note: If you are using 3rdparty Z-Wave Controller or Gateway, please refer to 3rdPartys instruction on how to add a new device to your network.Note 2: If the bulb will not join the network after repeated attempts, please use the Factory Reset procedures to clear the bulbs settings.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
Our RGBW bulb has three functional categories: Good, Better and Best. Good is your basic On, Off and Dim. Using your app and controller/gateway, you can turn your lights on, off and dim them down to 5% brightness from anywhere in the world, using your smartphone. At 2700K and 800 lumens, it is a true 60W equivalent. At Better, this is where the innovative technology takes over. You get your basic On, Off and Dim, but now you have the ability to tune the white color from a warm 1800K to a cool 6500K. The ability to tune the white is what we call Tunable White, or TW. The last functional category is Best. With Best, not only do you get On, Off, Dim, and Tunable White, but now we add the colors of Red, Green and Blue. This lighting is what we call RGBW. With LeedarsonsRGBW bulbs, you will get full, saturated colors that are true Reds, true Greens and true Blues. Having this capability allows combinations of 16 Million colors. With all of our lighting, and the app that supports it, you can group lights together, set different lighting scenes for different groups and set schdules to autotmatically turns lights, and groups, on and off. Automatically turning your lights on and off when youre away, gives the impression you are actually home and this will help deter unwanted entry.
| Reset to factory default |
Physically switch the bulb on and off six (6) times for intervals of 0.5-2 seconds. After the 6th time, the bulb will flash twice indicating that its successfully reset.A factory default is performed when the bulb is excluded from the Z-Wave network.Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
| Inclusion |
1. Screw the RGBW bulb into a standard E27 socket.2. Turn on the bulb with your wall switch to apply power to the bulb. a) If youre not using a wall switch, then use your alternate method to apply power to the bulb.3. Activate the included/excluded mode on your Z-wave controller or gateway.a) This may also be done through your associated app, if your ecosystem has that capability.4. Toggle the wall-switch, from OFF, then to ON. a) Or use your alternate method to toggle power from OFF, then to ON. 5. The LED bulb will flash once if it has been successfully included/ excluded into your Z-Wave network.Note: If you are using 3rdparty Z-Wave Controller or Gateway, please refer to 3rdPartys instruction on how to add a new device to your network.Note 2: If the bulb will not join the network after repeated attempts, please use the Factory Reset procedures to clear the bulbs settings. |
| Exclusion |
1. Screw the RGBW bulb into a standard E27 socket.2. Turn on the bulb with your wall switch to apply power to the bulb. a) If youre not using a wall switch, then use your alternate method to apply power to the bulb.3. Activate the included/excluded mode on your Z-wave controller or gateway.a) This may also be done through your associated app, if your ecosystem has that capability.4. Toggle the wall-switch, from OFF, then to ON. a) Or use your alternate method to toggle power from OFF, then to ON. 5. The LED bulb will flash once if it has been successfully included/ excluded into your Z-Wave network.Note: If you are using 3rdparty Z-Wave Controller or Gateway, please refer to 3rdPartys instruction on how to add a new device to your network.Note 2: If the bulb will not join the network after repeated attempts, please use the Factory Reset procedures to clear the bulbs settings. |
| NIF |
XXXNIF |
| Wakeup |
XXXWakeupDescription |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
1 |
Z-Wave Plus Lifeline |
Technical Data
| Hardware Platform |
ZM5101 |
| Device Type |
Light Dimmer Switch |
| Network Operation |
Always On Slave |
| Firmware Version |
HW: 255 FW: 2.00 |
| Z-Wave Version |
6.51.09 |
| Certification ID |
ZC10-17035475 |
| Z-Wave Product Id |
0x0300.0x0003.0x0003 |
| Communications Protocol |
Manufacturer Proprietary Protocol |
| Firmware Updatable |
Updatable by Manufacturer |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
