Aeotec
Range Extender 6
SKU: ZW117-G17
Quickstart
This is a
Turn the primary controller of Z-Wave network into inclusion mode, press the Z-Wave Button on Range Extender 6.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Aeotec Range Extender is a Z-Wave mesh network repeater which can extend the range of communication between Z-Wave products and assist other devices to reach each other in your Z-Wave network. The Range Extender can also communicate securely via AES 128 wireless Z-Wave commands and supports Over-The-Air (OTA) firmware upgrades.
| Reset to factory default | Press and hold the Z-Wave Button for 20 seconds and then release it.Use this procedure only in the event that your primary network controller is missing or inoperable. |
| Inclusion | Turn the primary controller of Z-Wave network into inclusion mode, press the Z-Wave Button on Range Extender 6. |
| Exclusion | Turn the primary controller of Z-Wave network into exclusion mode, pressthe Z-Wave Button on Range Extender 6. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | The association group 1 is the Z-Wave Lifeline group. The Device Reset Locally Notification CC can be sent to the associated node in association group 1. |
Configuration Parameters
Parameter 200: Partner ID
Set the partner ID of product. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Other partners. |
| 0 | Aeon Labs standard product |
Parameter 252: Enable/disable Lock Configuration
Enable/disable to lock Configuration parameters. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Parameter 254: Device tag
Set a device tag for your Range Extender. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 - 32767 | The available value range is 1 to 32767. |
Parameter 255: Reset the Range Extender
Reset the Range Extender to factory default. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Reset all configuration parameters to factory default settings |
| 1431655765 | Reset the bulb to factory default. |
Parameter 33: Set the RGB value of the LED.
Set the RGB value of the LED.Note: this parameter is only used to test the RGB LED, if you want to set its default RGB value, please use the Color Switch CC. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 256 - 65535 | Green color value |
| 1 - 255 | Bule color value |
| 65536 - 16777215 | Red color value |
Parameter 82: Set the default status ofthe LED when the Range Extender relays Z-Wave message
Set the default status ofthe LED when the Range Extender relays Z-Wave message Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The Green LED will remain ON for 2 seconds. |
| 1 | The LED remains OFF state. |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Repeater |
| Network Operation | Always On Slave |
| Firmware Version | HW: 117 FW: 1.04 |
| Z-Wave Version | 6.51.09 |
| Certification ID | ZC10-17075705 |
| Z-Wave Product Id | 0x0086.0x0A04.0x0075 |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | White |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |