Quickstart
This is a
secure
Notification Sensor for XXXQFrequencyName.
To run this device please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
1.Put the Z-Wave Controller into inclusion mode.2.Press the tamper switch 3 times within 1.5 seconds to put the unit into inclusion mode.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
The AC136 Panic Button is a Z-Wave Plus enabled device and is fully compatible with any Z-Wave enabled network. The device can be set up in a Z-wave network to communicate directly with other end devices such as lighting controllers, or to report directly a Z-wave controller.The Panic Button is a portable wireless switch designed to control the Panic/Disarm status of other associated devices thru the Z-Wave controller. After receiving the signals emitted by the Panic Button, the Z-Wave controller can then give commands or operate according to its own settings. Its great compatibility with Z-Wave products makes it suitable for smart home cloud based platforms.
Reset to factory default |
Please use this procedure only when the network primary controller is missing or otherwise inoperable.1. Press the tamper switch 3 times within 1.5 seconds to put the unit into exclusion mode.2. Within 1 second of step 1, press the tamper switch again and hold for 5 seconds.3.Node ID is excluded. The device reverts to factory default state. |
Inclusion |
1.Put the Z-Wave Controller into inclusion mode.2.Press the tamper switch 3 times within 1.5 seconds to put the unit into inclusion mode. |
Exclusion |
1. Put the Z-Wave Controller into exclusion mode.2. Press the tamper switch 3 times within 1.5 seconds to put the unit into exclusion mode. |
NIF |
XXXNIF |
Wakeup |
After it has been included into a Z-wave network, the detector will go to sleep but will send a Wakeup Notification Command periodically at preset period to the controller. The detector will stay awake for 10 seconds at least and then go back to sleep to conserve battery life.The time interval between Wakeup Notification Commands can be set in the Wakeup Command Class based on the range values below: Minimum Wake Up Interval600s (10 minutes)Maximum Wake Up Interval86400s (1 day)Default Wake Up Interval14400s (4 hours)Wake Up Interval Step Seconds600s (10 minutes) |
Protection |
XXXProtection |
FirmwareUpdate |
XXXFirmwareUpdate |
SetAssociation |
XXXSetAssociation |
Association Groups:
Group Number |
Maximum Nodes |
Description |
1 |
1 |
Association with 1 node. |
2 |
4 |
Association with 4 nodes(i.e. end devices such as smart plugs and other lighting controllers).This allows the On/Off module to receive commands directly from these end devices without the participation of the controller. |
Technical Data
Hardware Platform |
SD3502 |
Device Type |
Notification Sensor |
Network Operation |
Reporting Sleeping Slave |
Firmware Version |
HW: 1 FW: 1.01:00.01 |
Z-Wave Version |
6.71.01 |
Certification ID |
ZC10-17105824 |
Z-Wave Product Id |
0x0060.0x000A.0x0002 |
Supported Notification Types |
Appliance |
Switch Type |
Push Button |
Color |
White |
Firmware Updatable |
Updatable by Consumer via Internet |
Frequency |
XXfrequency |
Maximum transmission power |
XXantenna |