Honeywell
Plug-in Switch (Dual Plug Simultaneous Control)
SKU: 39342 / ZW4106
Quickstart
This is a
Adding your device to a Z-Wave network:1. Follow the instructions for your Z-Wave certified controller toinclude the device to the Z-Wave network.2. Once the controller is ready to include your smart switch,single press and release the manual/program button on thesmart switch to include it in the network.Now you have complete control to turn your lamp ON/OFFaccording to groups, scenes, schedules and interactiveautomations programmed by your controller.If your Z-Wave certified controller features Remote Access,you can now control your lighting from your mobile devices
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Transform any home into a smart home with the Honeywell Z-Wave Switch and Appliance Module. The lighting control enables wireless control of on/off functions for standard table and floor lamps, and is compatible with incandescent, LED, Xenon, Halogen, fluorescent and compact fluorescent bulbs. Easily controlled by your mobile device or computer using any Z-Wave certified gateway, the space-saving horizontal module plugs into a standard wall receptacle without blocking the second outlet or obstructing placement of furniture. It provides dual simultaneous Z-Wave enabled outlets for the lamp or appliance that you would like to control. Perfect for plug-in fans, lamps, and more! Take control of your home lighting with Honeywell Z-Wave Smart Controls!
| Reset to factory default | To return your switch to factory defaults:1. If plugged in, unplug the device from the receptacle.2. Press and hold the top button, plug the device in, and continue to hold for at least 3 seconds.Note: This should only be used in the event your networksprimary controller is missing or otherwise inoperable. |
| Inclusion | Adding your device to a Z-Wave network:1. Follow the instructions for your Z-Wave certified controller toinclude the device to the Z-Wave network.2. Once the controller is ready to include your smart switch,single press and release the manual/program button on thesmart switch to include it in the network.Now you have complete control to turn your lamp ON/OFFaccording to groups, scenes, schedules and interactiveautomations programmed by your controller.If your Z-Wave certified controller features Remote Access,you can now control your lighting from your mobile devices |
| Exclusion | To exclude and reset the device:1. Follow the instructions for your Z-Wave certified controller toexclude a device from the Z-Wave network.2. Once the controller is ready to Exclude your device, pressand release the manual/program button on the smart switchto exclude it from the network. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
| 2 | 5 | Basic Set and is controlled with the local load |
| 3 | 5 | Basic Set and is controlled by double pressing the On or Off button |
Configuration Parameters
Parameter 3: LED Light
When shipped from the factory, the LED is set to turn ON when theconnected light is turned OFF. This is the default setting and canbe changed if your primary controller supports the node configurationfunction. To make the LED turn ON when the light is turnedON, change parameter 3s value to 1. To turn the LED OFF at alltimes, change parameter 3s value to 2. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | On |
| 2 | Off |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 5.22 |
| Z-Wave Version | 6.51.10 |
| Certification ID | ZC10-17115840 |
| Z-Wave Product Id | 0x0039.0x5052.0x3033 |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | White |
| Switch Type | Push Button Illuminated |
| Loads Controlled | 2 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |