This is a
1. Set primary controller/gateway into inclusion mode (Please refer to your primarycontrollers manual on how to turn your controller into inclusion).2. Make sure the wall controller does not belong to any Z-Wave network (please refer tothe part How to check whether the wall controller included to a network of this manual).3. Short press the inclusion/exclusion button, or press and hold down ALL ON/OFFbutton for over 3 seconds, the wall controller will be set to inclusion mode, and waiting tobe included, then LED indicator turns on and blinks 6 times quickly to indicatesuccessful inclusion.Once the wall controller quits inclusion mode, the LED indicator will turns off. Thereare 3 methods for the wall controller to quit inclusion mode:1. Automatically quits after successful inclusion.2. Quits after 25 seconds timeout.3. Press and hold down ALL ON/OFF button for over 3 seconds, or short press theinclusion/exclusion button to quit.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
The Wall controller is a Security Enabled Z-Wave Plus device that can both control other Z-Wave devices and activate scenes in Gateways. The wall controller can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All nonbattery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Press and hold down inclusion/exclusion button for over 8 seconds, LED indicator turns on and shows 3 short blinks and 1 long blink to indicate successful factory reset, release inclusion/exclusion button, the wall controller will restart automatically.If this controller is the primary controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to exclude and re-include all of the nodes in the network.If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or otherwise inoperable.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Z-Wave Plus Lifeline;1. Send Command Class Device ResetLocally to associated devices of thisgroup to report factory reset informationwhen factory reset the wall controller.2. Double click a group number of the wallcontroller to send scene activationcommand to associated devices of thisgroup using Command Class CentralScene. |
2 | 12 | Press button u00221u0022 to activate group in orderto switch the associated devices with aBasic Set (by pressing the central buttononce) or dim these devices by using thefour lower buttons (or the dim wheelaround the central button). |
3 | 12 | Press button u00222u0022 to activate group in orderto switch the associated devices with aBasic Set (by pressing the central buttononce) or dim these devices by using thefour lower buttons (or the dim wheelaround the central button). |
4 | 12 | Press button u00223u0022 to activate group in orderto switch the associated devices with aBasic Set (by pressing the central buttononce) or dim these devices by using thefour lower buttons (or the dim wheelaround the central button). |
5 | 12 | Press button u00224u0022 to activate group in orderto switch the associated devices with aBasic Set (by pressing the central buttononce) or dim these devices by using thefour lower buttons (or the dim wheelaround the central button). |
Hardware Platform | ZM5101 |
Device Type | Wall Controller |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.10 |
Z-Wave Version | 6.71.01 |
Certification ID | ZC10-17115883 |
Z-Wave Product Id | 0x0330.0x0003.0xa10d |
Firmware Updatable | Updatable by Consumer by RF |
Z-Wave Scene Type | Central Scene |
Security V2 | S2_UNAUTHENTICATED |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |