This is a
1) Open the cover.2) Place the device within the direct range of your Z-Wave controller.3) Set the main controller in add mode (see the controllers manual).4) Click the Z-button once or triple click the Z-button quickly, the LED indicator should blink fast. 5) Wait for the adding process to end.6) Successful adding will be confirmed by the Z-Wave controllers message.
LEAK SENSORis capable of both detecting leaks and floods and when the level of water gets too low in pool or tank, LEAK SENSOR can work with your z-wave network to prevent emergencies such as burst water boiler to leaking air conditioners. With Z-Wave, the scope to save money is endless.The features list:1)Z-Wave Plus certified for wide compatibility (500 serials product).2)Security 0 and security 2 framework implemented with AES-128 encryption.3)Contains an extension water detecting probe. 4)Temperature measurement.5)Vibration sensor.6)The battery life is up to 1 year. 7)Low battery alert
Reset to factory default | 1) Power on the device2) Press and hold the Z button for more than 20 seconds,3) If holding time more than 20seconds, the LED indicator will keep on for 2 seconds, which means resetting is complete.4) The reset feature works only when the device has been included into a Z-Wave network.Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
Inclusion | 1) Open the cover.2) Place the device within the direct range of your Z-Wave controller.3) Set the main controller in add mode (see the controllers manual).4) Click the Z-button once or triple click the Z-button quickly, the LED indicator should blink fast. 5) Wait for the adding process to end.6) Successful adding will be confirmed by the Z-Wave controllers message. |
Exclusion | 1) Open the cover.2) Place the device within the direct range of your Z-Wave controller.3) Set the main controller remove mode (see the controllers manual).4) Triple click the Z-button quickly, the LED indicator should blink fast.5) Wait for the removing process to end.6) Successful adding will be confirmed by the Z-Wave controllers message. |
NIF | XXXNIF |
Wakeup | Press and hold the Z button for more than 5 seconds and release. |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline:1. Notification Report.Sensor will send Notification Report to the associated nodes 2. Battery Report.Sensor will send Battery Report when the battery level is low and the battery reports value is 0xFF.3. Device Reset Locally Notification.Sensor will send Device Reset Locally Notification when reset4.Sensor multilevel reportWhen associated to Group 1, you can adjust the temperature reporting cycle according to the configuration settings. |
2 | 5 | 1. Basic Set.Flood Sensor will send Basic Set to associated nodes when Water leak detected. |
Flood sensor can send BASIC SET command to nodes associated with group 2. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Flood sensor can reverse its value of BASIC SET when flooding is triggered. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Send BASIC SET VALUE = 255 to nodes associated with group 2 when flooding alarm is triggered.Send BASIC SET VALUE = 0 to nodes associated with group 2 when flooding alarm is canceled. |
1 | Send BASIC SET VALUE = 0 to nodes associated with group 2 when flooding alarm is triggered.Send BASIC SET VALUE = 255 to nodes associated with group 2 when flooding alarm is canceled. |
Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
-128 - 127 | The higher the value, the long the report periodically - in hexadecimal values from 0x01 to 0xFF, or 1 to 255 if your controller allows unsigned decimal values. |
0 | Disable flooding alarm |
Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 1 | when the value is 0, the product will not sends a vibration alarm after moving or shaking; when the value is 1, the product will sends a vibration alarm after moving or shaking |
The temperature changes at least 1 degree Celsius before reported. Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
-128 - 127 | the higher the value ,the long the report time |
The precision of the temperature value is 1.Available settings(US):-670 - 2570-67257FAvailable settings(Other):-550 - 1250-55125CDefault setting (US): 1040 (104F)Default setting (Other): 400(40C) Size: 2 Byte, Default Value: 1040
Setting | Description |
---|---|
-670 - 2570 | the larger the value , the higher the high temperature(US) |
-550 - 1250 | the larger the value , the higher the high temperature(other) |
The precision of the temperature value is 1.Available settings(US):-670 - 2570-67257FAvailable settings(Other):-550 - 1250-55125CDefault setting (US): 320 (32F)Default setting (Other): 0 (0C) Size: 2 Byte, Default Value: 320
Setting | Description |
---|---|
-670 - 2570 | the smaller the value , the lower the low temperature(US) |
-550 - 1250 | the smaller the value , the lower the low temperature(other) |
0 Disable.1 Enable. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 - 1 | when the value is 0, the product will not alarm when being triggered; when the value is 1, the product will alarm when being triggered |
This parameter defines a battery level as the low battery.Available settings: 10-50 (10% - 50%)Default setting: 20 (20%) Size: 1 Byte, Default Value: 20
Setting | Description |
---|---|
10 - 50 | Set the trigger value for the low battery alarm |
Hardware Platform | ZM5202 |
Device Type | Notification Sensor |
Network Operation | Reporting Sleeping Slave |
Firmware Version | HW: 2 FW: 1.01 |
Z-Wave Version | 6.71.01 |
Certification ID | ZC10-17125906 |
Z-Wave Product Id | 0x000C.0x0201.0x000A |
Supported Notification Types | Heat AlarmHome SecurityWater Alarm |
Sensors | Air Temperature |
Color | White |
Firmware Updatable | Updatable by Consumer by RF |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |