This is a
Autoinclusion - This feature allow you to add hard to reach devices to Z-Wave network. 3-times ON and OFF the power roller shutter (OFF-ON-OFF-ON-OFF-ON) causes the introduction of roller shutter to Autoinclusion mode. Please note that the procedure has been started the time between on and off can not exceed 20s. Autoinclusion mode is activated for a maximum of 10 minutes. During this time, we can add an awning to any Z-Wave controller running in the Include procedure.Include - This function allow you to add roller shutter to the network Z-Wave. Follow the procedur adding device to the network Z-Wave according to user manual supplied with the product. Then, press the programming button P on the roller shutter for 1 second.
FAKRO ARZ Z-Wave external roller shutters have been adapted for wireless cooperation with the Z-Wave system. The shutter is designed for FAKRO roof windows and its installation is possible at any time after roof window installation. It is also possible to use the shutter for roof windows of other manufactures. Installed on the outside of the window, the roller shutter constitutes an optimum solution against overheating and provides additional protection of the window e.g. against falling tree branches etc. The roller shutter enables complete blackout and good sound reduction. It is also good protection from glazing excessive cooling during the winter. The roller shutter also means increased security. It has built-in overload protection and can be controlled by using standard Z-Wave controller.The AMZ Z-Waveroller shutter has three extremes: - Maximum extension (encoder maximum position)- Completely rolled up (encoder minimum position)- Current limiting protecting awning blind against damage and user against accidental injury resulting from the contact with moving elements of awning blind.There are three association groups in roller shutter ARZ Z-Wave:1.Life Linegroup for position reporting roller shutter after each a stoppage and alarm reporting (overcurrent, damage encoders). This group can be a maximum 1 device.2.Basic Repeatgroup used to transfer the received basic commands to the devices included in this group. This group can be a maximum 5 devices.3.Multilevel Repeatgroup used to transfer the received multilevel commands to the devices included in this group. This group can be a maximum 5 devices.Technical Parameters: Power voltage: 15V DCRated current: 1,4 ACurrent limit: YESSpeed: 23 r.p.mTemperature of usage: (-10 C) do (65C) Supplying cable: 2 x 0,75mm2
Reset to factory default | Device Reset LocallyThis function allows you to reset the Z-Wave network without the use of Z-Wave controller. Press 5 times the programming button P fast, the roller shutter was removed from the Z-Wave network, restore the default parameters, name and locations. Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
Inclusion | Autoinclusion - This feature allow you to add hard to reach devices to Z-Wave network. 3-times ON and OFF the power roller shutter (OFF-ON-OFF-ON-OFF-ON) causes the introduction of roller shutter to Autoinclusion mode. Please note that the procedure has been started the time between on and off can not exceed 20s. Autoinclusion mode is activated for a maximum of 10 minutes. During this time, we can add an awning to any Z-Wave controller running in the Include procedure.Include - This function allow you to add roller shutter to the network Z-Wave. Follow the procedur adding device to the network Z-Wave according to user manual supplied with the product. Then, press the programming button P on the roller shutter for 1 second. |
Exclusion | Exclude - This function allow you to remove roller shutter from the network Z-Wave. Follow the procedur removing device from the network Z-Wave according to user manual supplied with the product. Then, press the programming button P on the roller shutter for 1 second. Function removes information only about newtork Z-Wave. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Z-Wave Plus Lifeline, group for position reporting roller shutter after each a stoppage and alarm reporting (overcurrent, damage encoders) |
2 | 5 | Basic Repeatgroup used to transfer the received basic commands to the devices included in this group. |
3 | 5 | Multilevel Repeatgroup used to transfer the received multilevel commands to the devices included in this group. |
Value describe the calibration status Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 2 | Value 1calibrated, Value 2discalibratedto enter the calibration mode must first time discalibrate and then calibrate. |
Value describe the end position of roller shutter. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 2 | 1FF go to Max, 2FF go to previous position |
Hardware Platform | ZM5202 |
Device Type | Window Covering - Pos/End Aware |
Network Operation | Always On Slave |
Firmware Version | HW: 23 FW: 1.01:01.01 |
Z-Wave Version | 6.61.00 |
Certification ID | ZC10-18015975 |
Z-Wave Product Id | 0x0085.0x0003.0x0011 |
Switch Type | Push Button with Indicator |
Window Covering Control Features | Endpoint AwareManual CalibrationPosition AwareSupports Open/Close MotionSupports Up/Down Motion |
Supported Notification Types | Power ManagementSystem |
Outdoor Use | ok |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |