This is a
Add for inclusion 1.Ensure the led bulb has been excluded outside the network.2.Triggered by OFF ->ON (between 0.5-2 seconds each time)3.LED solid yellow Color (0xFFFF00) during the pairing(Timeout is 10 seconds).Failure:Blinks between 100% White and Red 0x0000FF color for 3 seconds (at a rate of 200ms per flash), Once 3 seconds have passed, the LED should return to a Warm White LED at 100%Success:Blinks between 100% White and Green 0x00FF00 color for 3 seconds (at a rate of 200ms per flash). Once 3 seconds have passed, the LED should return to a Warm White LED at 100%.
Standard form factor and appearance of the light bulb with 800 lm output RGBW: dimmable from 5% to 100%, tunable from 1800K to 6500K, and 16 million colors Possible to be included in groups, scenes, or schedules Suitable for indoor lighting: Corridors, Bedroom, Living Room, etc.
Reset to factory default | Reset the Device.1.Assuming led bulb was added to controller and was power on.2.RGBW bulb re-power 6 times (between 0.5-2 seconds each time).Note: ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON 3.If the 6th power on, the led bulb change to Yellow color(into pairing process ), which means that the reset factory settings are successf.Using this action in case of the primary controller is missing or inoperable. |
Inclusion | Add for inclusion 1.Ensure the led bulb has been excluded outside the network.2.Triggered by OFF ->ON (between 0.5-2 seconds each time)3.LED solid yellow Color (0xFFFF00) during the pairing(Timeout is 10 seconds).Failure:Blinks between 100% White and Red 0x0000FF color for 3 seconds (at a rate of 200ms per flash), Once 3 seconds have passed, the LED should return to a Warm White LED at 100%Success:Blinks between 100% White and Green 0x00FF00 color for 3 seconds (at a rate of 200ms per flash). Once 3 seconds have passed, the LED should return to a Warm White LED at 100%. |
Exclusion | Remove for exclusion 1.Assuming led bulb was added to controller.2.Triggered by OFF -> ON -> OFF -> ON -> OFF -> ON (between 0.5-2 seconds each time).3.LED Solid Purple/Violet Color (0xEE82EE) during the unpairing process. (Timeout is 10 seconds).Failure:Blinks between 100% White and Red 0x0000FF color for 3 seconds (at a rate of 200ms per flash), Once 3 seconds have passed, the LED should return to the last color ( memory status(color cc set)) of LED Bulb.Success:Blinks between 100% White and Blue 0x0000FF color for 3 seconds (at a rate of 200ms per flash). Once 3 seconds have passed, the LED should return to a Warm White LED at 100%. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Set Configuration parameter 0x50 0: nothing.1: Send the Basic Report.2. Send Device Reset Locally CC |
User custom mode for LED animations.0 = Disable custom mode.1= Blink Colors in order mode.2=Randomized blink color mode Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable custom mode |
1 | Blink Colors in order mode. |
2 | Randomized blink color mode |
Ramp rate when dimming using Multilevel Switch V1 CC in 100msValue range = 0x00 -0x64 Size: 1 Byte, Default Value: 20
Setting | Description |
---|---|
0 - 100 | Specifying the ramp rate when dimming using Multilevel Switch V1 CC in 100ms |
Enable/Disable Strobe over Custom Color.0 = Disable.1 = Enable.Others = Ignore. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable Strobe over Custom Color. |
1 | Enable Strobe over Custom Color. |
Set the rate of change to next color in Custom Mode.Value1 ~ Value4:Value Range = 5 - 8640000 (50 - 86400000ms) Size: 1 Byte, Default Value: 50
Setting | Description |
---|---|
5 - 8640000 | Set the specified rate of change to next color in Custom Mode. |
Set color that LED Bulb blinks in (Blink Mode)Value range =0x01-0xFF Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 - 255 | Set color that LED Bulb blinks in (Blink Mode) |
Enable to send notifications to associated devices(Group 1) when the state of LED Bulb is changed.0 = Nothing.1= Basic CC report. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Nothing |
1 | Send basic report to associated devices when the state of the LED Bulb is changed |
The user can configure the parameter to adjust the color component Warm White. Value range =Warm White(0x0A8C(2700k) ~ 0x1387 (4999k)) Size: 2 Byte, Default Value: 2700
Setting | Description |
---|---|
2700 - 4999 | Value range =Warm White(0x0A8C(2700k) ~ 0x1387 (4999k)) |
The user can configure the parameter to adjust the color component Cold White. Value rang = Cold White (0x1388 (5000k) ~ 0x1964 (6500k)) Size: 2 Byte, Default Value: 6500
Setting | Description |
---|---|
5000 - 6500 | Value rang = Cold White (0x1388 (5000k) ~ 0x1964 (6500k)) |
Hardware Platform | ZM5101 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.13 |
Z-Wave Version | 6.51.09 |
Certification ID | ZC10-18036069 |
Z-Wave Product Id | 0x0371.0x0103.0x0002 |
Firmware Updatable | Updatable by Consumer by RF |
Color | White |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |