Qolsys Inc.
Z-Wave Plug-In Dimmer
SKU: QZ2140-840
Quickstart
This is a
1. Place your network controller into inclusion mode by following the controller manufacturer's instructions.2. When the controller is ready, single click the button on the front of the IQ Dimmer. The controller should indicate that the new device was added successfully.3. Once the IQ Dimmer has been successfully added to your home network, you can move it to the preferred location in the home
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The IQ Dimmer is a Z-Wave Plus certified device with S2 security and SmartStart features. You can now add this device securely and with ease using QR code on the product with compatible gateways supporting S2 and SmartStart. The IQ Dimmer communicates with other Z-Wave certified devices and updates your home into a smart home. The IQ Dimmer can be used to turn any plug in lamps into a smart lamp with dimmable light bulbs, turning it On, Off, or control dimming wirelessly. Each Z-Wave device also serves as a node to repeat the signal in the network, thus, extending the overall Z-Wave mesh wireless network range.Additional Features: Power 120 VAC, 60Hz, up to 300 watts Region US: 908.4, 916 MHz Works w/ most incandescent, dimmable CFL & LED lights Plugs into Standard AC outlet Remotely controls On, Off, or Dim levels Control lights via schedule LED backlit manual On/Off button Second wall AC outlet remains free Works with any certified gateway supporting Z-Wave
| Reset to factory default | 1. Unplug the IQ Dimmer from the AC outlet and also unplug the power plugs of the lighting from the module (if plugged in)2. Press and hold the button on the IQ Dimmer3. Plug the IQ Dimmer back into the AC outlet with the button pressed. After 3 seconds, release the button. If you see the button blink, that means that IQ Dimmer has been reset successfully.Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
| Inclusion | 1. Place your network controller into inclusion mode by following the controller manufacturer's instructions.2. When the controller is ready, single click the button on the front of the IQ Dimmer. The controller should indicate that the new device was added successfully.3. Once the IQ Dimmer has been successfully added to your home network, you can move it to the preferred location in the home |
| Exclusion | 1. Place your network controller into exclusion mode by following the controller manufacturer's instructions.2. When the controller is ready, single click the button on the front of the IQ Dimmer. The controller should indicate that the new device was removed successfully.3. Once the IQ Dimmer has been successfully added to your home network, you can move it to the preferred location in the home |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | 1. Z-Wave Plus Lifeline2. Device Reset Locally Notification |
Configuration Parameters
Parameter 10: Timer
Parameter 10 indicates the time duration of each level. Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | Valid Values: 1-255,indicates the time duration of each level. |
Parameter 3: Night Light
The LED indicator will be OFF when the connected light is ON and vice versa.When value =0 the LED indicator will be OFF when the the connected light is ON, and the LED will be ON when the connected light is OFF. If value =1 the LED indicator will be ON when the connected light is ON, and the LED indicator will be OFF when the connected light is OFF. If value =2 the LED indicator will always be OFF regardless of the load status Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 2 | When value =0 the LED indicator will be OFF when the the connected light is ON, and the LED will be ON when the connected light is OFF. If value =1 the LED indicator will be ON when the connected light is ON, and the LED indicator will be OFF when the connected light is OFF. If value =2 the LED indicator will always be OFF regardless of the load status |
Parameter 9: Dimming Resolution Level
Parameter 9 indicates the number of dimming levels. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | Valid Values: 1-99, indicates the number of dimming levels. |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 50.03 |
| Z-Wave Version | 6.81.00 |
| Certification ID | ZC10-18046088 |
| Z-Wave Product Id | 0x012A.0x4744.0x3032 |
| Firmware Updatable | Updatable by Consumer by RF |
| Outdoor Use | ok |
| Color | White |
| Electric Load Type | Dimmable FluorescentDimmable LEDFluorescentIncandescentLED |
| Switch Type | Push Button Illuminated |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |