Sharp Corporation
Multi Sensor
SKU: DN3G6JA069
Quickstart
This is a
Insert a CR123A, and LED blinks. Set the controller to the status for Add.Press the button over 3 seconds and release.About 30 second later, LED turns off when Add is completed.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The Multi Sensor is a product for IoT with several sensors and with functions of Z-Wave communication. It can collect sensing data that temperature, humidity, Luminance, human motion, and door open/close by using a magnet. And it sends the data to the gateway.The Multi Sensor has the following general features:-Z-Wave communication-Sensing with the followingTemperature sensor,Humidity sensor,Luminance sensor,Human detect sensor (motion sensor by pyroelectric infrared sensor),Open/Close sensor (detecting the opening and shutting of the door by using a magnet),Tamper switch.
| Reset to factory default | Press the button over 10 seconds and release. |
| Inclusion | Insert a CR123A, and LED blinks. Set the controller to the status for Add.Press the button over 3 seconds and release.About 30 second later, LED turns off when Add is completed. |
| Exclusion | Set the controller to the status for Remove.Press the button over 3 seconds and release.LED blinks when Remove is completed. |
| NIF | XXXNIF |
| Wakeup | Briefly press the button once. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 1: Enable switch of Multilevel Sensor report
Configure arbitrarily to send which sensor values. The sensor values can be selected from Humidity, Luminance, and Temperature. Size: 1 Byte, Default Value: 7
| Setting | Description |
|---|---|
| 0 | Humidity disable, Luminance disable, Temperature disable |
| 1 | Humidity disable, Luminance disable, Temperature enable |
| 2 | Humidity disable, Luminance enable, Temperature disable |
| 3 | Humidity disable, Luminance enable, Temperature enable |
| 4 | Humidity enable, Luminance disable, Temperature disable |
| 5 | Humidity enable, Luminance disable, Temperature enable |
| 6 | Humidity enable, Luminance enable, Temperature disable |
| 7 | Humidity enable, Luminance enable, Temperature enable |
Parameter 2: Enable switch of Alarm Notification report
Configure to send which the sensor values arbitralily. The sensor values can be selectedfrom Human Detect and Open/Close. Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 | Human Detect disable, Open/Close disable |
| 1 | Human Detect disable, Open/Close enable |
| 2 | Human Detect enable, Open/Close disable |
| 3 | Human Detect enable, Open/Close enable |
Parameter 3: Select switch of Luminance Sensor scale
Configure the Luminance Sensor scale to either percentage value or Lux. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Percentage value |
| 1 | Lux |
Parameter 4: Set interval for Multilevel Sensor
Configure the sending interval time of the sensor value which is selected by configuration parameter number 1.u00220u0022 means especially synchronizing withWake Up Interval. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | synchronizing with Wake Up Interval |
| 1 - 65535 | The setting unit is seconds. |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 255 FW: 0.80 |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-18066133 |
| Z-Wave Product Id | 0x010B.0x4761.0x0069 |
| Sensors | Air TemperatureHumidityLuminanceMotion/No Motion (Binary)Open/Closed (Binary) |
| Supported Notification Types | Home Security |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |