Zooz
Z-Wave Plus Motion Sensor
SKU: ZSE18
Quickstart
This is a
AUTO-INCLUSION:Initiate inclusion in the Z-Wave interface. Activating the battery will automatically put the sensor into inclusion mode. If its not added within 30 seconds, try resetting it and including it manually.MANUAL INCLUSION:1. Bring the sensor within direct range of your Z-Wave gateway (hub).2. Put the Z-Wave hub into inclusion mode.3. Press and release the Z-Wave button 3 times quickly. The LED indicator will start blinking fast and turn solid for a second to confirm inclusion.3. A new motion sensor will appear in your device list.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
PRODUCT FEATURES:- Fast, reliable motion detection- Built-in vibration sensor- Latest S2 security protocol and AES-128 signal encryption- 2 alternative power sources: battery or micro USB- Auto-inclusion for instant set-up- Visual range test tool- Magnetic mount for quick and flexible installation- Adjustable LED indicator- Low battery alerts- Z-Wave Plus with improved 500 chip for faster and safer wirelesscommunication
| Reset to factory default | If your primary controller is missing or inoperable, you may need to reset the device to factory settings.To complete the reset process manually, press and HOLD the Z-Wave button on the sensor for at least 20 seconds. The LED indicator will flash, stay solid, and then turn off to confirm factory reset.NOTE: All previously recorded activity and custom settings will be erased from the devices memory. |
| Inclusion | AUTO-INCLUSION:Initiate inclusion in the Z-Wave interface. Activating the battery will automatically put the sensor into inclusion mode. If its not added within 30 seconds, try resetting it and including it manually.MANUAL INCLUSION:1. Bring the sensor within direct range of your Z-Wave gateway (hub).2. Put the Z-Wave hub into inclusion mode.3. Press and release the Z-Wave button 3 times quickly. The LED indicator will start blinking fast and turn solid for a second to confirm inclusion.3. A new motion sensor will appear in your device list. |
| Exclusion | 1. Bring the sensor within direct range of your Z-Wave gatewaycontroller (hub).2. Put the Z-Wave hub into exclusion mode.3. Press and release the Z-Wave button on the sensor 3 times asquickly as possible.4. Your hub will confirm exclusion and the device will disappearfrom your controller's device list. |
| NIF | XXXNIF |
| Wakeup | MANUAL WAKE-UPPress and HOLD the Z-Wave button for 5 seconds to wake the deviceup. The LED will start flashing. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
| 2 | 5 | Basic Set |
Configuration Parameters
Parameter 12: PIR Sensitivity
Use it to adjust PIR sensor sensitivity. Size: 1 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 1 - 8 | 1 = low sensitivity and 8 = high sensitivity |
Parameter 14: BASIC SET for Group 2
Use it to enable or disable BASIC SET reports when motion is triggered for Group 2 of associated devices. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
Parameter 15: BASIC SET for Group 2 Reversed Values
Use it to reverse values sent in BASIC SET reports when motion is triggered for Group 2 of associated devices. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | BASIC SET value 255 is sent when motion is triggered, BASIC SET value 0 is sent when motion times out |
| 1 | BASIC SET value 0 is sent when motion is triggered, BASIC SET value 255 is sent when motion times out. |
Parameter 17: Vibration Sensor
Use it to disable the vibration sensor. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | vibration sensor is disabled |
| 1 | vibration sensor is enabled |
Parameter 18: Motion Retrigger Interval
Use it to set trigger interval - the time when motion is reported again after initial trigger. Size: 2 Byte, Default Value: 27
| Setting | Description |
|---|---|
| 3 - 65535 | 3 stands for 6 seconds and 65535 stands for 65538 seconds (add 3 seconds to each value number). |
Parameter 20: LED Indicator
Use it to disable the LED indicator. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | LED Indicator is disabled |
| 1 | LED Indicator is enabled |
Parameter 32: Low Battery Reports
Use it to set battery level for low battery reports. Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 10 - 50 | 10 stands for 10% battery left and 50 stands for 50% battery left |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.00 |
| Z-Wave Version | 6.71.01 |
| Certification ID | ZC10-18066135 |
| Z-Wave Product Id | 0x027A.0x0201.0x0006 |
| Supported Notification Types | Home Security |
| Color | White |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |