HomeSeer
Door/Window Sensor
SKU: HS-DS100+
Quickstart
This is a
1.Insert the AAA battery.2.Set the Z-Wave network main controller into learning mode.3.Triple or single short press the Z-button.4.If the add for inclusion is successful, the LED will blink less than 5 seconds and then keep on 3 seconds. Otherwise, the LED will blink 5 seconds and then turn off, in which case you need to repeat the process from step 2.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Door/Window Sensor is a wireless reed sensor powered by AAA battery. It is used for detecting the opening or closing of doors, windows. It can communicate with an associated Z-Wave device, such as Siren, Smart Switch, etc.
| Reset to factory default | 1.Insert the AAA battery.2.Pressing and holding the Z button for more than 20 seconds,3.Led will keep on until the Z-Button is released, and it will reset to factory default when the button is released.Using this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
| Inclusion | 1.Insert the AAA battery.2.Set the Z-Wave network main controller into learning mode.3.Triple or single short press the Z-button.4.If the add for inclusion is successful, the LED will blink less than 5 seconds and then keep on 3 seconds. Otherwise, the LED will blink 5 seconds and then turn off, in which case you need to repeat the process from step 2. |
| Exclusion | 1.Insert the AAA battery.2.Set the Z-Wave network main controller into learning mode.3.Triple clicking the Z-button.4.If the remove for exclusion, the LED will turn off within 1 second. Otherwise, the LED will blink 5 seconds and then turn off, in which case you need to repeat the process from step 2. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Door/Window Sensor will send notification report and battery report to the associated nodes. |
| 2 | 5 | Sensor will send Basic Set to the associated nodes when the sensor body and magnet removed or combined. |
Configuration Parameters
Parameter 15: Value of the BASIC SET
Door/Window Sensor can reverse its value of BASIC SET when the magnet is triggered. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Send BASIC SET VALUE = 255 to nodes associated with group 2 when door/window is opened.Send BASIC SET VALUE = 0 to nodes associated with group 2 when door/window is closed. |
| 1 | Send BASIC SET VALUE = 0 to nodes associated with group 2 when door/window is opened.Send BASIC SET VALUE = 255 to nodes associated with group 2 when door/window is closed. |
Parameter 32: Level of low battery
This parameter defines a battery level as the low battery. Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 10 - 50 | the value here defines the "low battery" |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 1 FW: 2.00 |
| Z-Wave Version | 6.81.00 |
| Certification ID | ZC10-18066165 |
| Z-Wave Product Id | 0x000C.0x0201.0x0008 |
| Supported Notification Types | Access ControlHome Security |
| Sensors | Open/Closed (Binary) |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |