Aibase
Smart Plug
SKU: HA-ZW-5PAB
Quickstart
This is a
To add the product to the Z-Wave network:a. Make sure that the Smart Plug has been connected to the power supply.b. Set the Z-Wave network main controller into inclusion mode.c. Power on.d. The LED will blink fast until the inclusion is completed and then the LED will keep turning on or off. Otherwise, the LED will still blink slowly, in which you need to repeat the process from step b
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Flexibility: AC output on/off by manual or remote by APP Remote Control: Power on/off any device connecting to smart plug manually or by APP Power consumption: Measures the energy consumption of the connected devices. Schedule: setting your lights connected to Plug to turn on and off on a schedule. Z-wave Wireless signal repeater
| Reset to factory default | Reset Smart Plug to factory default:1. Make sure that the Smart Plug has been connected to the power supply.2. Press and hold the Button for 5 seconds.3. If holding time is more than one second, the LED will blink faster and faster. If holding time is more than 5 seconds, the LED will be solid for 3 seconds to indicate that the resetting is successful. Otherwise, repeat step 2.Note:Reset to factory will remove Smart Plug from the Z-Wave network. Use this procedure only in the event that the network primary controller missing or otherwise inoperable. |
| Inclusion | To add the product to the Z-Wave network:a. Make sure that the Smart Plug has been connected to the power supply.b. Set the Z-Wave network main controller into inclusion mode.c. Power on.d. The LED will blink fast until the inclusion is completed and then the LED will keep turning on or off. Otherwise, the LED will still blink slowly, in which you need to repeat the process from step b |
| Exclusion | To remove the product from the Z-Wave network:a. Insert the Smart Plug to power socket, the LED will follow the status (on or off) of its loads power level.b. Set the Z-Wave network main controller into exclusion mode.c. Short press Button 3 times within 1.5 second.d. The LED will blink fast until the exclusion is completed, then the LED will keep on blinking slowly. Otherwise, the LED will keep on blink fast for 35 seconds and then follow the status (on or off) of its load status. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | 1. When the state of Smart Plug (turn on or off the load) is changed: 1. Set Configuration parameter 0x03 to 0: Do not send Basic Report 2. Set Configuration parameter 0x03 to 1: Send Basic Report 3. Set Configuration parameter 0x03 to 2: Send Basic Report only when Load condition is changed not by Z-WAVE Command, such as short pressing. 2. Sending Meter Report. |
Configuration Parameters
Parameter 1: Overcurrent protection
Smart Plug keep detecting the load power, once the AC current exceeds 16.5A for more than 4 seconds, smart plug's relay will turn off. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | The function is disabled |
| 1 | The function is enabled |
Parameter 100: Setting the parameters 101~104 to the default states.
Setting the parameters 101~104 to the default states. Size: 1 Byte, Default Value: 85
| Setting | Description |
|---|---|
| 85 | Available settings |
Parameter 101: Setting time for sending meter report (watt)
The interval time of sending meter report (watt) to associated device (Group Lifeline). Size: 4 Byte, Default Value: 600
| Setting | Description |
|---|---|
| 5 - 2678400 | Available settings |
| 0 | The function is disabled. |
Parameter 102: Setting time for sending meter report (KWh)
The interval of sending meter report (KWh) to association device (Group Lifeline). Size: 4 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 5 - 2678400 | Available settings |
| 0 | The function is disabled |
Parameter 103: Setting time for sending meter report (voltage)
The interval of sending meter report (voltage) to association device (Group Lifeline). Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 5 - 2678400 | Available settings |
| 0 | The function is disabled |
Parameter 104: Setting time for sending meter report (current)
The interval time of sending meter report (current) to associated device (Group Lifeline). Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 5 - 2678400 | Available settings |
| 0 | The function is disabled |
Parameter 16: The value here represents minimum change in wattage (in terms of wattage) for a meter report to be sent
When the change value of load power exceeds the setting value, smart plug will send meter report (watt) to associated device (Group Lifeline). Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| -32768 - 32767 | Available settings |
| -32768 - -1 | 65535 to 32768 |
| 1 - 32767 | 1 to 32767 |
| 0 | The function is disabled. |
Parameter 17: The value here represents minimum change in wattage percent (in terms of percentage) for a meter report (watt) to be sent
When the change value of the load power exceeds the setting value, smart plug will send meter report to associated device (Group Lifeline). Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| -128 - 127 | Available settings |
| -128 - -1 | 255% to 128% |
| 1 - 127 | 1% to 127% |
| 0 | The function is disabled |
Parameter 2: Setting device status after power failure
Define how the Plug reacts after the power supply is back on. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Smart Plug memorizes its state after a power failure. |
| 1 | Smart Plug does not memorize its state after a power failure. Connected device will be on after the power supply is reconnected. |
| 2 | Smart Plug does not memorize its state after a power failure. Connected device will be off after the power supply is reconnected. |
Parameter 254: Enable/disable the configuration command
Lock/unlock all configuration parameters. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Unlock |
| 1 | Lock |
Parameter 3: Notification when Load status change
Smart Plug can send notifications to associated device (Group Lifeline) when the status of smart plugs load is changed. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | The LED status follows the load change. |
| 1 | when operating the load, The LED lights for 5 seconds and then turns off. |
Parameter 4: LED Load indicator mode selection
Configure LED Display mode to prevent light pollution at night. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The LED status follows the load change. |
| 1 | when operating the load, The LED lights for 5 seconds and then turns off. |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.00 |
| Z-Wave Version | 6.71.01 |
| Certification ID | ZC10-18076185 |
| Z-Wave Product Id | 0x0384.0x0200.0x000B |
| Firmware Updatable | Updatable by Consumer by RF |
| Switch Type | Push Button |
| Z-Wave Scene Type | Scene |
| Supported Meter Type | Electric Energy |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |