Quickstart
This is a
secure
Door Lock - Keypad for XXXQFrequencyName.
To run this device please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
1.check Z-WaveTM Controller entered inclusion mode.2.Press the Add/Remove functionenterPC is enter 0000(default)enterPC->enter-> 1 -> 0 ->enter3.After add successful, it will have twice beep sounds.if inclusion fail it will have five beep.Notice 1 : if you reset doorlock ,you have to do OPERATING INSTRUCTION no.1(door handling identification process )Notice 2:if Door lock in learn mode,device can stop on operation setting mode,until success include or 60s time out.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
This doorlock PSA03 is a security enabled wireless device, based on Z-Wave technology,It can open/close door via wireless controll , and can set/remove usercode.when manually open/ close door, it can report . low battery warning it can report.
| Reset to factory default |
1.Press the black key in battery cover, and until 5s time up.device can beep two times.2.Device can send resetlocally notificationnote : Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
| Inclusion |
1.check Z-WaveTM Controller entered inclusion mode.2.Press the Add/Remove functionenterPC is enter 0000(default)enterPC->enter-> 1 -> 0 ->enter3.After add successful, it will have twice beep sounds.if inclusion fail it will have five beep.Notice 1 : if you reset doorlock ,you have to do OPERATING INSTRUCTION no.1(door handling identification process )Notice 2:if Door lock in learn mode,device can stop on operation setting mode,until success include or 60s time out. |
| Exclusion |
1.check Z-WaveTM Controller entered exclusion mode.2.Press the Add/Remove functionenterPC is enter 0000(default)enterPC->enter-> 1 -> 0 ->enter3.After remove successful, it will have twice beep sounds.if exclusion fail it will have five beep.Notice 1 : if you reset doorlock ,you have to do OPERATING INSTRUCTION no.1(door handling identification process )Notice 2:if Door lock in learn mode,device can stop on operation setting mode,until success include or 60s time out. |
| NIF |
XXXNIF |
| Wakeup |
XXXWakeupDescription |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
5 |
Group 1 name:LifenameGroup 1 command list:COMMAND_CLASS_BATTERY,COMMAND_CLASS_DOOR_LOCK_V2,COMMAND_CLASS_DEVICE_RESET_LOCALLY |
| 2 |
5 |
Group 2 name:Doorlock OpGroup 2 command list:COMMAND_CLASS_DOOR_LOCK_V2, |
Technical Data
| Hardware Platform |
SD3502 |
| Device Type |
Door Lock - Keypad |
| Network Operation |
Listening Sleeping Slave |
| Firmware Version |
HW: 255 FW: 0.10 |
| Z-Wave Version |
6.81.01 |
| Certification ID |
ZC10-18076194 |
| Z-Wave Product Id |
0x013C.0x000A.0x0069 |
| Door Lock Type |
Lever Handle |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
