Aeotec
WallMote Quad
SKU: ZW130-D
Quickstart
This is a
Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action button that you can find on the product's housing.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Aeotec WallMote is an intelligent Z-Wave remote controller that mounted on a wall. It has 4 touch buttons that you can easily control the Z-Wave devices in your home network via touching, long pressing or sliding the button areas. Its surface has a RGB LED to indicate the button actions also accompanied by touch beep and vibration. The WallMote is also a security Z-Wave device and supports Over The Air (OTA) feature for the products firmware upgrade.
| Reset to factory default | Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is missing or inoperable. |
| Inclusion | Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action button that you can find on the product's housing. |
| Exclusion | Turn the primary controller of Z-Wave network into exclusion mode, short press the products Action button that you can find on the product's housing. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline.When touching the Button 1 to 4, the Central Scene Notificcation command will be sent to the associated node (1) in Association group 1. |
| 2 | 5 | When touching the Button 1, the Basic Set command will be sent to the associated nodes in Association group 2. |
| 3 | 5 | When touching the Button 1, the Multilevel Switch Set command will be sent to the associated nodes in Association group 3. |
| 4 | 5 | When touching the Button 2, the Basic Set command will be sent to the associated nodes in Association group 4. |
| 5 | 5 | When touching the Button 2, the Multilevel Switch Set command will be sent to the associated nodes in Association group 5. |
| 6 | 5 | When touching the Button 3, the Basic Set command will be sent to the associated nodes in Association group 6. |
| 7 | 5 | When touching the Button 3, the Multilevel Switch Set command will be sent to the associated nodes in Association group 7. |
| 8 | 5 | When touching the Button 4, the Basic Set command will be sent to the associated nodes in Association group 8. |
| 9 | 5 | When touching the Button 4, the Multilevel Switch Set command will be sent to the associated nodes in Association group 9. |
Configuration Parameters
Parameter 1: Enable/disable the touch sound.
Enable/disable the touch sound. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Parameter 11: To set which Command would be sent to the associated nodes in association group 2, 4, 6, 8.
To set which Command would be sent to the associated nodes in association group 2, 4, 6, 8. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Baisc Set |
| 1 | Switch Binary Set |
Parameter 2: Enable/disable the touch vibration.
Enable/disable the touch vibration. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Parameter 252: Enable/disable to lock all configuration parameters.
Enable/disable to lock all configuration parameters. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Parameter 255: Reset the Mote
Reset the Mote to factory default. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Reset all configuration parameters to factory default setting |
| 1431655765 | Reset to factory default setting and removed from the z-wave network |
Parameter 3: Enable/disable the function of button slide.
Enable/disable the function of button slide. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Parameter 39: Set the low battery value.
Set the low battery value.. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 5 - 50 | The value range is 5% to 50%. |
Parameter 4: To configure which report will be sent when pressing the buttons.
To set which notification would be sent to the associated devices (Group 1) when pressing the buttons. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | Send Central Scene Command Notification |
| 3 | Send Central Scene Command Notification and Configuration report |
Parameter 81: Enable/ disable to blink the orange Led when WallMote sends out Wake Up Notification
Enable/ disable to blink the orange Led when WallMote sends out Wake Up Notification. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Parameter 82: Enable/ disable to blink the blue Led (or yellow Led if low battery) for 3 seconds before it changes to red when the button control message is failed to be sent out.
Enable/ disable to blink the blue Led (or yellow Led if low battery) for 3 seconds before it changes to red when the button control message is failed to be sent out. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Parameter 83: Enable/ disable to light ON the orange Led when WallMote is in USB charging.
Enable/ disable to light ON the orange Led when WallMote is in USB charging. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disable, the orange LED will blink 3 times and then be OFF once the WallMote is USB powered on. |
| 1 | Enable. |
Parameter 84: Enable/ disable the Led indication when pressing the control buttons
Enable/ disable the Led indication when pressing the control buttons Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Wall Controller |
| Network Operation | Portable Slave |
| Firmware Version | HW: 130 FW: 2.03 |
| Z-Wave Version | 6.61.01 |
| Certification ID | ZC10-18116310 |
| Z-Wave Product Id | 0x0086.0x0302.0x0082 |
| Firmware Updatable | Updatable by Consumer by RF |
| Z-Wave Scene Type | Central Scene |
| Supported Notification Types | Power Management |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |