This is a
This ON/OFF plug supports Auto Inclusion feature where it will automatically enter Inclusion mode when first powered up after a factory reset.1. There is an ON/OFF button on the front of the device which is used to carry out inclusion, exclusion or association.2. Put your Z-Wave Controller into inclusion/exclusion mode.3. Plug this ON/OFF Plug-in module into a wall outlet near the load to be controlled.4. The Inclusion process should be completed when the LED stops blinking.Note: If Auto Inclusion fails, refer to the Troubleshooting section regarding Manual InclusionIf auto inclusion fails:1. Put the Z-Wave Controller into Inclusion mode2. Press the ON/OFF button 3 times within1.5 seconds to put the unit into Inclusion mode
Eatons Z-Wave Plus Wireless ON/OFF Plug-in module can be used to provide local and remote wireless ON/OFF control of a single outlet. Controlled outlet can be manually and remotely controlled by commands sent from your compatible Z-Wave certified controller leaving the other outlet always ON.Provides wireless control of one outlet leaving the other outlet always ON Rated for up to 12A plug loads and up to 300W of LEDsCan be associated with up to 4 other devicesSupports Z-Wave Plus functionality with S2 security certificationVoice and app based control when used with compatible Z-Wave controller or Eatons home automation hub
Reset to factory default | Please use this procedure only when the network primary controller is missing or otherwise inoperable1. Press the ON/OFF button 3 times within1.5 seconds to put the unit into exclusion mode2. Within 1 second of step 1, press and hold thebutton for 5 seconds3. Node ID is deleted. The device reverts to factorydefault state |
Inclusion | This ON/OFF plug supports Auto Inclusion feature where it will automatically enter Inclusion mode when first powered up after a factory reset.1. There is an ON/OFF button on the front of the device which is used to carry out inclusion, exclusion or association.2. Put your Z-Wave Controller into inclusion/exclusion mode.3. Plug this ON/OFF Plug-in module into a wall outlet near the load to be controlled.4. The Inclusion process should be completed when the LED stops blinking.Note: If Auto Inclusion fails, refer to the Troubleshooting section regarding Manual InclusionIf auto inclusion fails:1. Put the Z-Wave Controller into Inclusion mode2. Press the ON/OFF button 3 times within1.5 seconds to put the unit into Inclusion mode |
Exclusion | 1. Put the Z-Wave Controller into Exclusion mode2. Press the ON/OFF button 3 times within1.5 seconds to put the unit into Exclusion mode |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 4 | Z-Wave Plus Lifeline |
2 | 4 | Basic SetWhen the button on the unit is pressed, the unit will send a Basic Set command to the nodes of Group 2. When the unit is OFF, Basic Set Value = 0x00. When the unit is ON, Basic Set Value = 0xFF |
1: remember (0: do not remember) Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Do not remember last status |
1 | Remember last status |
Hardware Platform | SD3502 |
Device Type | On/Off Power Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.01:00.01 |
Z-Wave Version | 6.71.01 |
Certification ID | ZC10-18126336 |
Z-Wave Product Id | 0x001A.0x0053.0x0050 |
Electric Load Type | ELV (Electronic)FluorescentIncandescentInductive (e.g. Motor)LEDMLV (Magnetic) |
Z-Wave Scene Type | Central Scene |
Color | White |
Supported Notification Types | Appliance |
Loads Controlled | 2 |
Firmware Updatable | Updatable by Consumer by RF |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |