This is a
Automatic mode1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.2. Once the controller is ready to add your sensor, slide the battery door down and remove (if not mounted to door or window).3. Remove the plastic battery tab. This activates the sensor and starts the auto-add process. The red LED will begin to flashquickly as it searches for a network. The sensor will attempt to search for a network for two minutes, after which, it will time out.4. The red LED will continue to flash quickly after it locates a networkthe controllers app will indicate if it has discovered the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product. Enter the 5-digit code.5. The red LED will activate for 3 seconds to confirm the sensor has been added in the network.Manual mode1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.2. Once the controller is ready to add your sensor, ensure battery is installed with the correct polarity in the sensor and the battery tab has been removed.3. Press and release the programming button. This starts the manual add process. The red LED will begin to flash quickly as it begins the add process.4. The red LED will activate for 3 seconds to confirm the sensor has been added in the network.5. The controllers app will indicate if it has discovered the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product. Enter the 5-digit code.
By simply opening or closing your door or window, the sensor uses Z-Wave technology to wirelessly trigger scenes throughout your home. From your mobile device, youre able to schedule lights to turn on as soon as you walk in and be notified of activity while youre away. The sensor is discreetly designed to blend subtly into the frame of the door, adding the convenience of the Smart Door/Window Sensor to your home without distracting from your household decor.
Reset to factory default | 1. Press the programming button 10 times within 6 seconds (interval between presses of the button cannot be longer than 1 second).2. The red LED will activate for 2 seconds, followed by 3 quick flashes.- Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
Inclusion | Automatic mode1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.2. Once the controller is ready to add your sensor, slide the battery door down and remove (if not mounted to door or window).3. Remove the plastic battery tab. This activates the sensor and starts the auto-add process. The red LED will begin to flashquickly as it searches for a network. The sensor will attempt to search for a network for two minutes, after which, it will time out.4. The red LED will continue to flash quickly after it locates a networkthe controllers app will indicate if it has discovered the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product. Enter the 5-digit code.5. The red LED will activate for 3 seconds to confirm the sensor has been added in the network.Manual mode1. Follow the instructions for your Z-Wave certified controller to add the sensor in the Z-Wave network.2. Once the controller is ready to add your sensor, ensure battery is installed with the correct polarity in the sensor and the battery tab has been removed.3. Press and release the programming button. This starts the manual add process. The red LED will begin to flash quickly as it begins the add process.4. The red LED will activate for 3 seconds to confirm the sensor has been added in the network.5. The controllers app will indicate if it has discovered the sensor. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the back of the box, or the QR code label on the product. Enter the 5-digit code. |
Exclusion | 1. Follow the instructions for your Z-Wave certified controller to remove the sensor from the Z-Wave network.2. Once the controller is ready to remove your sensor, press and release the programming button on the sensor 1 time to remove it from the network.3. The red LED will blink 5 times to indicate it has been removed. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline |
This parameter allows you to reverse the detection values of the device. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | (Default) Disabled |
1 | Reverse event (Open 16, Close 17) |
This parameter allows you to enable the alternate exclusion method that is available for this device. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | (Default) Disabled |
1 | Enabled |
This parameter allows you to change the inclusion configuration settings of this device. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | (Default) - Notification Only |
2 | Notification and Basic Report |
This parameter gives you the option to turn the LED off on magnetic triggers. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | (Default) - Enabled |
1 | Disabled |
This parameter allows you to choose how often the battery level is reported. Size: 2 Byte, Default Value: 1440
Setting | Description |
---|---|
5 - 60 | 5-60 Minutes |
360 | 6 Hours |
720 | 12 Hours |
1440 | (Default) Daily |
This parameter allows you to choose how often the LED will flash once the device/battery cover is tampered with. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | (Default) Continuous Flash |
2 | Flashes once, on initial tamper only |
Hardware Platform | ZM5202 |
Device Type | Notification Sensor |
Network Operation | Reporting Sleeping Slave |
Firmware Version | HW: 255 FW: 5.55 |
Z-Wave Version | 6.81.01 |
Certification ID | ZC10-19016363 |
Z-Wave Product Id | 0x0063.0x4953.0x3235 |
Firmware Updatable | Updatable by Consumer by RF |
Sensors | Open/Closed (Binary) |
Supported Notification Types | Home Security |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |