Aeotec
NanoMote Quad
SKU: ZWA003-S
Quickstart
This is a
NanoMote Quad can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.1. Insert the LIR2450 battery.2. Place the device within the direct range of your Z-Wave controller.3. Set the main controllers adding mode (see the controllers manual).4. Double click the button quickly, the LED indicator should blink fast.5. Wait for the adding process to end.6. Successful adding will be confirmed by the Z-Wave controllers message.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
NanoMote Quad is a wireless, portable and rechargeable product. On one hand, it can be used to control separate Z-Wave device, such as a smart Plug, smart Dimmer, Bulb, etc. through Z-Wave Gateway. On the other hand, it can also be used to program a scene by Gateway app which groups many smart nodes such as Plugs, Bulbs, and Siren... The scene may refer to sleep scene, movie scene and entertainment scene, etc. as you created.
| Reset to factory default | Press and hold the button for 20 seconds, the LED light will be solid on in red. Then release the button, the LED light will be stay in red for 2 seconds, during this 2 seconds, please click the button once, it will start to restore factory default. At the same time, the LED light will be solid on in colorful for 15 seconds. Then Sending Device Reset locally notification to the controller.NOTE:Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. |
| Inclusion | NanoMote Quad can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.1. Insert the LIR2450 battery.2. Place the device within the direct range of your Z-Wave controller.3. Set the main controllers adding mode (see the controllers manual).4. Double click the button quickly, the LED indicator should blink fast.5. Wait for the adding process to end.6. Successful adding will be confirmed by the Z-Wave controllers message. |
| Exclusion | To remove the NanoMote Quad from the Z-Wave network:1.Insert the LIR2450 battery.2.Place the device within the direct range of your Z-Wave controller.3.Set the main controller remove mode (see the controllers manual).4.Double click the button quickly, the LED indicator should blink fast.5.Wait for the removing process to end.6.Successful adding will be confirmed by the Z-Wave controllers message. |
| NIF | XXXNIF |
| Wakeup | Pressing and holding button for 5 seconds and then release so the NanoMote Quad will wake up itself and send wake-up notification out to Z-Wave Controller. After that, it can be operated to update parameters, OTA, and detect battery level etc. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Lifeline |
| 2 | 5 | On/Off control,Button 1 |
| 3 | 5 | Dimming control,Button 1 |
| 4 | 5 | On/Off control,Button 2 |
| 5 | 5 | Dimming control,Button 2 |
| 6 | 5 | On/Off control,Button 3 |
| 7 | 5 | Dimming control,Button 3 |
| 8 | 5 | On/Off control,Button 4 |
| 9 | 5 | Dimming control,Button 4 |
Configuration Parameters
Parameter 32: Level of low battery
Level of low battery Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 10 - 50 | Available settings: 10-50 (10% - 50%) |
Parameter 41: Enable send central scene notification
Enable send central scene notification. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 - Disable. |
| 1 | 1Enable. |
Parameter 42: Setting the duration value of the command switch multilevel
Setting the duration value of the command switch multilevel. Size: 1 Byte, Default Value: -128
| Setting | Description |
|---|---|
| -128 - 127 | Available settings: -128 ---127 |
Parameter 43: Enable/disable the buzzer alarm when batteryisrunninglow
Enable/disable the buzzer alarm when batteryisrunninglow. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 - Disable. |
| 1 | 1 Enable. |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Wall Controller |
| Network Operation | Portable Slave |
| Firmware Version | HW: 1 FW: 1.02 |
| Z-Wave Version | 6.71.01 |
| Certification ID | ZC10-19036389 |
| Z-Wave Product Id | 0x0371.0x1C02.0x0003 |
| Z-Wave Scene Type | Scene & Central Scene |
| Firmware Updatable | Updatable by Consumer via Internet |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |