LG U+ IoT@Home
Smart Switch
SKU: SSD-105
Quickstart
This is a
After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Power Strip.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
This device is a smart light switch using 1 wire AC line.You can control the light from the remote.Input AC power : 220Vthis has one button.
| Reset to factory default | With the device powered, press and hold the third button for 10 seconds.The LED of the button will flash red after 5 seconds, it will turn green, then it will flash red again. Then release the button.After a few moments, the entire LED is blinking and the green LED stops flashing.Please use the procedure only in the event that the network primary controller is missing or otherwise inoperable. |
| Inclusion | After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Power Strip. |
| Exclusion | After mounting the UZB controller to your PC and run the PC Controller program you can click the Remove button in the PC Controller program. Press the button on the Smart Power Strip for more than five seconds after you plug the Smart Power Strip into a power outlet will Exclusion in the network controller, while the flashing red button LED Smart Power Strip. |
| NIF | XXXNIF |
| Wakeup | To wake up this device, either press the switch button or try remote control. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline,Profile General = 0x00Profile General Lifeline = 0x01Command Class - Device Reset Locally Notification - Notification Report - Multilevel Sensor Report - Version Report - Configuration Report -Battery Report |
| 2 | 5 | OnOff Noti EP 1Porfile Notification = 0x71Command Class- Notification Report |
Configuration Parameters
Parameter 1: change report cycle
This parameter determines the period in which the temperature and humidity values are transmitted. default Value : 0x258 (integer 600 --> 10 minutes) Size: 2 Byte, Default Value: 600
| Setting | Description |
|---|---|
| 60 - 3600 | If value is 0x258, The device reports temperature and humidity every 10 minutes. |
Parameter 2: report value due to temperature change rate
This parameter determines the amount of temperature change that must be reported. (Temperature Variation / 0x14 (integer 20 -> 2.0C) In the receiving part, divide this value by 10 and treat it as one decimal place.) Default Value : 0x14 Possible value : 0x0a ~ 0x1E Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 10 - 30 | the value is set to 20 and If there is a change in temperature above 2 degrees, the temperature is reported regardless of the reporting period. |
Parameter 3: report value due to humidity change rate
This parameter determines the amount of humidity change that must be reported (Humidity Variation / 0x0A (integer 10 -> 10%)) Default Value : 0x0A Possible values : 0x05~0x14 Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 5 - 20 | The value is set to 10 and If there is a change in humidity above 10 %, the humidity is reported regardless of the reporting period. |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | On/Off Power Switch |
| Network Operation | Listening Sleeping Slave |
| Firmware Version | HW: 3 FW: 39.47 |
| Z-Wave Version | 6.81.03 |
| Certification ID | ZC10-19046432 |
| Z-Wave Product Id | 0x018C.0x0057.0x0001 |
| Switch Type | Push Button with Indicator |
| Outdoor Use | ok |
| Supported Notification Types | Heat Alarm |
| Firmware Updatable | Updatable by Manufacturer Representative |
| Sensors | Humidity |
| Electric Load Type | FluorescentIncandescentLED |
| Color | White |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |