Quickstart

This is a secure Light Dimmer Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
1. Set primary controller/gateway into inclusion mode (Please refer to your primary controllers manual on how to turn your controller into inclusion).2. Power on the in-wall dimmer and set it into inclusion mode. There are two methods to set the in-wall dimmer into inclusion mode:1)Repower on the dimmer, it will be set into inclusion mode automatically, and waiting to be included.2)Triple press the action button on the dimmer, it will set the dimmer into inclusion mode.The connected light will stay solid on for 3 seconds to indicate successful inclusion.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

The micro smart dimmer is a Z-Wave device designed to work with various types of light sources. It may beconnected to two-wire or three-wire configuration so it can operate with or without neutral lead. Thedimmer can switch or dim connected light source either through Z-Wave devices or through the wallswitch connected directly to it. The smart dimmer is equipped with an algorithm of smart light sourcedetection which makes configuration easier and ensures high compatibility of the device. It may be usedas a switch with non-dimmable light sources (in 3-wire connection).

Reset to factory default	Press and hold down the action button for over 10 seconds, the dimmer will be reset to factory defaults.Note: Factory reset is not recommended for exclusion, please use this procedure only if the primary controller/gateway is missing or otherwise inoperable.
Inclusion	1. Set primary controller/gateway into inclusion mode (Please refer to your primary controllers manual on how to turn your controller into inclusion).2. Power on the in-wall dimmer and set it into inclusion mode. There are two methods to set the in-wall dimmer into inclusion mode:1)Repower on the dimmer, it will be set into inclusion mode automatically, and waiting to be included.2)Triple press the action button on the dimmer, it will set the dimmer into inclusion mode.The connected light will stay solid on for 3 seconds to indicate successful inclusion.
Exclusion	There are two exclusion methods:Method 1: Exclusion from the primary controller/gateway as follows:1. Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on how to set your controller into exclusion).2. Triple press the action button, the dimmer will be set to exclusion mode, and waiting to be excluded, then the dimmer will be excluded from the network.Method 2: Factory reset the dimmer will force it to be excluded from a network. (please refer to the part Factory Reset of this manual)Note: Factory reset is not recommended for exclusion, please use this procedure only if the primary controller/gateway is missing or otherwise inoperable.
NIF	XXXNIF
Wakeup	XXXWakeupDescription
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	5	dimmer, send u0022Device Reset Locally Notification CCu0022 to associateddevices of this group to report factory reset information.2. When load state changes, send u0022Basic Report CCu0022 to associateddevices of this group.3. When a load over current is detected, send u0022Over-currentdetectedu0022 to Lifeline.4. When a mains voltage drop is detected, send u0022Voltage drop/driftu0022 to Lifeline.5. When over temperature is detected, send Emergency shutoffstatusu0022 to Lifeline.

Configuration Parameters

Parameter 10: Enable/disable to detect load after re-power on

Enable/disable to detect load after re-power on(detect load type, minimum brightness,maximum brightness)Note: When the device does not belong to anynetwork, load detection will be enabled everytime after re-power on. When the device hasalready been added to a network, load detectionwill be disabled.
Size: 1 Byte, Default Value: 0

Setting Description
0 disable

1 enable to detect every time after re-power on

2 enable to detect only after first re-power on

Setting	Description
0	disable
1	enable to detect every time after re-power on
2	enable to detect only after first re-power on

Parameter 11: Wiring type

Wiring typeNote: this parameter is read only
Size: 1 Byte, Default Value: 0

Setting Description
0 unknown

1 2 Wire With No Neutral

2 3 Wire With Neutral

Setting	Description
0	unknown
1	2 Wire With No Neutral
2	3 Wire With Neutral

Parameter 12: Load type

Load typeNote: this parameter is read only
Size: 1 Byte, Default Value: 0

Setting Description
0 unknown

1 resistive

2 inductive

3 capacitive

Setting	Description
0	unknown
1	resistive
2	inductive
3	capacitive

Parameter 13: Enable/disable over current protection

Enable/disable over current protection (over 1.5A for 20 seconds continuously)
Size: 1 Byte, Default Value: 1

Setting Description
0 disable

1 enable

Setting	Description
0	disable
1	enable

Parameter 14: Power automatic report absolute threshold, unit is W

Power automatic report absolute threshold, unit is WWhen power changes above the absolutethreshold, immediately report current power value
Size: 2 Byte, Default Value: 10

Setting Description
0 - 32767 When power changes above the absolute threshold, immediately report current power value

Setting	Description
0 - 32767	When power changes above the absolute threshold, immediately report current power value

Parameter 15: Power automatic report percentage threshold, unit is %

Power automatic report percentage threshold, unit is %When power changes above the percentage threshold, immediately report current power value
Size: 1 Byte, Default Value: 20

Setting Description
0 - 100 When power changes above the percentage threshold, immediately report current power value

Setting	Description
0 - 100	When power changes above the percentage threshold, immediately report current power value

Parameter 2: Saving load state before power failure

Saving load state before power failure
Size: 1 Byte, Default Value: 2

Setting Description
0 shutoff load

1 turn on load

2 save load state before power failure

Setting	Description
0	shutoff load
1	turn on load
2	save load state before power failure

Parameter 21: Power metering automatic report time cycle, unit is second

Power metering automatic report time cycle, unit is second
Size: 4 Byte, Default Value: 600

Setting Description
5 - 2678400 Power metering automatic report time cycle, unit is second

Setting	Description
5 - 2678400	Power metering automatic report time cycle, unit is second

Parameter 22: Energy metering automatic report time cycle, unit is second

Energy metering automatic report time cycle, unit is second
Size: 4 Byte, Default Value: 1800

Setting Description
5 - 2678400 Energy metering automatic report time cycle, unit is second

Setting	Description
5 - 2678400	Energy metering automatic report time cycle, unit is second

Parameter 23: Voltage metering automatic report time cycle, unit is second

Voltage metering automatic report time cycle, unit is second
Size: 4 Byte, Default Value: 3600

Setting Description
5 - 2678400 Voltage metering automatic report time cycle, unit is second

Setting	Description
5 - 2678400	Voltage metering automatic report time cycle, unit is second

Parameter 24: Current metering automatic report time cycle, unit is second

Current metering automatic report time cycle, unit is second
Size: 4 Byte, Default Value: 3600

Setting Description
5 - 2678400 Current metering automatic report time cycle, unit is second

Setting	Description
5 - 2678400	Current metering automatic report time cycle, unit is second

Parameter 3: Enable/disable to send the basic report

Enable/disable to send the basic report to the Lifeline when the load state changed (When value set as 1, re-power on the dimmer, it will send Basic report automatically
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable to send Basic report

1 Enable to send Basic report

Setting	Description
0	Disable to send Basic report
1	Enable to send Basic report

Parameter 4: Default fade time

Default fade time (unit is second)
Size: 1 Byte, Default Value: 1

Setting Description
0 Instantly

1 - 127 1 second (0x01) to 127 seconds (0x7F) in 1 second resolution.

Setting	Description
0	Instantly
1 - 127	1 second (0x01) to 127 seconds (0x7F) in 1 second resolution.

Parameter 5: Setting minimum brightness value

Setting minimum brightness value
Size: 1 Byte, Default Value: 0

Setting Description
0 - 50 the bigger the value is, the higher the loads minimum brightness is

Setting	Description
0 - 50	the bigger the value is, the higher the loads minimum brightness is

Parameter 6: Setting maximum brightness value

Setting maximum brightness value
Size: 1 Byte, Default Value: 100

Setting Description
0 - 100 the maximum brightness value

Setting	Description
0 - 100	the maximum brightness value

Parameter 7: Choose MOSFET driving type

Choose MOSFET driving type
Size: 1 Byte, Default Value: 0

Setting Description
0 trailing edge

1 leading edge

Setting	Description
0	trailing edge
1	leading edge

Parameter 8: External switch type

External switch type
Size: 1 Byte, Default Value: 0

Setting Description
0 Push button switch

1 normal on/off switch

2 3-way switch

Setting	Description
0	Push button switch
1	normal on/off switch
2	3-way switch

Parameter 9: Enable/disable external switch to be added to and removed from a network

Enable/disable external switch to be added to and removed from a network (when enables this function, triple press the external switch within 1.5 seconds to be added to or removed from a network)
Size: 1 Byte, Default Value: 1