This is a
Set your controller to add mode (see your controllers manual). Follow the instruction for Wake up. A long LED blink indicates that the add/remove was successful.
Strips, the ultra-thin multi sensor is now available in two new sensor models, Strips Drip and Strips Comfort. Drip and Comfort join Strips Guard, the thinnest magnet sensor in the world detecting if your windows are open and closed invisibly since 2015.Strip Drip sends an alarm signal if it detects a water leak. Its unique design allows it to be easily placed almost everywhere, including most places other sensors simply cant fit.With soaking pads integrated in the mounting plate even small amounts of water will be detected. The built-in temperature sensor gives the possibility to combine the leakage alarm with a freeze alarm. There is also a built-in ambient light sensor that may be useful in special applications.Strips Comfort is a very accurate temperature and ambient light sensor. The unique design and mounting plate makes it easy to place almost invisibly in your home to measure temperature or control heating, air conditioning and even windows blinds which are connected to your Z-Wave smart home system.All Strips products can be used both in-doors and out-doors and the integrated custom battery gives Strips an expected lifetime of up to 10 years. For you, this means no hassle needing to change or charge batteries in your Strips sensors for the lifetime of the products!
Reset to factory default | You may need to reset Strips if your Z-Wave controller is missing or not responding.Follow the instructions for Wake up, but on the 3rd repetition, leave the magnet at the rounded edge for 10 seconds. A long LED signal indicates success. |
Inclusion | Set your controller to add mode (see your controllers manual). Follow the instruction for Wake up. A long LED blink indicates that the add/remove was successful. |
Exclusion | Set your controller to remove mode (see your controllers manual). Follow the instruction for Wake up. A long LED blink indicates that the add/remove was successful. |
NIF | XXXNIF |
Wakeup | Wake up Strips manually for Z-Wave communication. Place the magnet at the rounded edge. When the LED blinks, move the magnet away. Repeat twice within 10 seconds. |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Z-Wave Plus Lifeline |
3 - 64000 Size: 4 Byte, Default Value: 40000
Setting | Description |
---|---|
3 - 64000 | High ambient light report level(4 bytes) |
1 - 42000(Must be significantly lower than parameter 10) Size: 4 Byte, Default Value: 5000
Setting | Description |
---|---|
1 - 42000 | (Must be significantly lower than parameter 10) |
0: Off1: On Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Off |
1 | On |
1 to 100(1= almost dry, 100= soaking wet) Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
1 - 100 | (1= almost dry, 100= soaking wet) |
0-120: Number of hours between moisture reports Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 120 | Number of hours between moisture reports |
0: Off1: On Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Off |
1 | On |
1: Normal2: Frequent Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Normal reporting |
2 | Frequent reporting |
0: Off1: On Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Off |
1 | On |
0: Celcius1: Fahrenheit Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Celcius |
1 | Fahrenheit |
0: Off1: On Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Off |
1 | On |
-20 to + 60 (degree C) Size: 1 Byte, Default Value: 60
Setting | Description |
---|---|
-20 - 60 | Temperature alarm level |
-20 to + 60 (degree C) Size: 1 Byte, Default Value: -20
Setting | Description |
---|---|
-20 - 60 | Temperature alarm level |
0: Off1: On2: Report only when levels defined in parameter 10 & 11 are passed Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Off |
1 | On |
2 | Report only when levels defined in parameter 10 & 11 are passed |
Hardware Platform | ZM5101 |
Device Type | Notification Sensor |
Network Operation | Reporting Sleeping Slave |
Firmware Version | HW: 3 FW: 0.07:00.07 |
Z-Wave Version | 6.51.10 |
Certification ID | ZC10-19056519 |
Z-Wave Product Id | 0x019A.0x0003.0x000A |
Outdoor Use | ok |
Supported Notification Types | Heat AlarmHome SecurityWater Alarm |
Sensors | Air TemperatureLuminanceMoisture |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |