Honeywell
Plug-in Dimmer (Single Plug)
SKU: 39443 / ZW3104
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Transform any home into a smart home with the Honeywell Z-Wave Plug-In Dimmer. The Dimmer enables wireless control of on/off and dim functions for standard incandescent table and floor lamps, as well as dimmable fluorescent, LED and CFL fixtures and more! Use the dimmer control to customize the lighting output and create the perfect ambiance for any room. The space-saving horizontal module plugs into a standard wall receptacle without blocking the second outlet or obstructing placement of furniture. The Dimmer provides one Z-Wave enabled outlet for the lamp you would like to control. Take control of your home lighting with Honeywell Z-Wave Smart Controls!
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Supports device reset locally and receives unsolicited status updates. |
| 2 | 5 | Association Group 2 supports Basic Set and is controlled with the local load |
| 3 | 5 | Association Group 3 supports Basic Set and is controlled by double pressing the button |
Configuration Parameters
Parameter 10: Dim Rate Adjustments (When Manually Controlled)
Timing of steps Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | Timing of steps |
Parameter 11: Dim Rate Adjustments (When Receiving All-On/Off Commands)
Number of steps or levels Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | Number of steps or levels |
Parameter 12: Dim Rate Adjustments (When Receiving All-On/Off Command
Timing of steps Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | Timing of steps |
Parameter 16: Enable/disable switch mode
Enable and disable switch mode Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Parameter 20: Minimum dim level
Set the minimum percentage the dimmer will go to when operating it at the switch Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | Number of Steps |
Parameter 3: LED Light
When shipped from the factory, the LED is set to turn ON when the connected light is turned On. This is the default setting and can be changed if your primary controller supports the node configuration function or by a manual method. To make the LED turn ON when the light is turned ON, change parameter 3s value to 1. To turn the LED OFF at all times, change parameter 3s value to 2. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | default |
| 1 | LED On when light is turned On |
| 2 | LED always Off |
Parameter 6: Dim up/down rate
Number of steps or levels Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Dim up/down the light to the specified level quickly by command except value 0 and FF |
| 1 | Dim up/down the light to the specified level slowly by command except value 0 and FF |
Parameter 7: Dim Rate Adjustments (From Z-Wave Controller)
Number of steps or levels Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | Number of steps or levels |
Parameter 8: Dim Rate Adjustments (From Z-Wave Controller)
Timing of steps Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | Timing of steps |
Parameter 9: Dime Rate Adjustments (When Manually Controlled)
Number of steps or levels Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | Number of steps or levels |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 5.24 |
| Z-Wave Version | 6.51.08 |
| Certification ID | ZC10-19126813 |
| Z-Wave Product Id | 0x0039.0x5044.0x3038 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |