Zooz
RGBW DIMMER ZEN31
SKU: ZEN31
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
FEATURES:- Manual or Z-Wave on/off, brightness, and RGBW color control- Perfect for programming your existing RGBW LED strip- Energy monitoring in live mode and over time- Double tap to full brightness feature + optional scene control- Remembers and restores on/off status after power failure- Built-in Z-Wave Plus signal repeater to extend network range- S2 security protocol and AES-128 bank-grade encryptionSPECIFICATIONS:- Model Number: ZEN31- Z-Wave Signal Frequency: 908.42 MHz- Power: 12 / 24 V DC (Do NOT connect to 120 V AC high-voltage power!)- Maximum Load: 10 A total between all channels (6 A per channel max); 120 W total when powered by 12 V DC / 240 W total when powered by 24 V DC- Range: Up to 100 feet line of sight - Operating Temperature: 32-104 F (0-40 C)- Installation and Use: Indoor only- Dimensions: 1.67 x 1.5 x 0.69
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 3 | reports the device status and allowsfor assigning single device only (main controller by default). |
| 2 | 5 | allows to synchronize state of other Zooz RGBW Dimmers ZEN31 - do not use with other devices. |
| 3 | 5 | is used to turn the associateddevices on/off reflecting IN1 operation. |
| 4 | 5 | is used to change brightness level ofassociated devices reflecting IN1 operation. |
| 5 | 5 | is used to turn the associateddevices on/off reflecting IN2 operation. |
| 6 | 5 | is used to change brightness level of associated devices reflecting IN2 operation. |
| 7 | 5 | is used to turn the associated devices on/off reflecting IN3 operation. |
| 8 | 5 | is used to change brightness level of associated devices reflecting IN3 operation. |
| 9 | 5 | is used to turn the associated devices on/off reflecting IN4 operation. |
| 10 | 5 | is used to change brightness level of associated devices reflecting IN4 operation. |
Configuration Parameters
Parameter 1: On Off Status After Power Failure
Set the on off status for the RGBW Dimmer after power failure. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | forced to OFF (regardless of state prior to power outage) |
| 1 | remem-bers and restores on/off status after power failure |
| 2 | forced to ON (regard-less of state prior to power outage) |
Parameter 150: RGBW / HSB Wall Switch Mode
Choose how switches connected to the input terminals control your LED strip. In the default RGBW mode, each switch connected to each input terminal controls the RGBW channels separately (so IN1 for red, IN2 for green, etc) with a single click for ON/OFF, double click to full brightness, and press-and-hold to dim (momentary switches only). In the HSB mode, IN1 controls hue, IN2saturation, IN3brightness, IN4white with single click for last set value or value 0, double click to max value, and press-and-hold to set custom value. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | RGBW mode (default) |
| 1 | HSB mode |
Parameter 151: Physical Ramp Rate
Adjust the ramp rate for your RGBW dimmer (fade-in / fade-out effect for on / off operation). Values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated from the connected wall switch. Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 | instant on/off |
| 1 - 127 | seconds |
| 128 - 254 | 1 - 127 minutes |
Parameter 152: Z-Wave Ramp Rate
Adjust the ramp rate for your RGBW dimmer when operated remotely from the Z-Wave hub. Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 | instant on/off |
| 1 - 127 | seconds |
| 128 - 254 | 1 - 127 minutes |
Parameter 154: Single Click ON Trigger for Associated Devices
Set the status or brightness level triggering other associated devices in your network if the dimmer is turned ON with a single click. Each of the 4 available bytes refers to one channel, starting with IN1 and ending with IN4. This setting applies to basic set and switch multilevel commands sent to associated devices in the appropriate association group. Size: 4 Byte, Default Value: 255
| Setting | Description |
|---|---|
| 0 - 99 | custom brightness level |
| 255 | ON |
Parameter 155: Single Click OFF Trigger for Associated Devices
Set the status or brightness level triggering other associated devices in your network if the dimmer is turned OFF with a single click. Each of the 4 available bytes refers to one channel, starting with IN1 and ending with IN4. This setting applies to basic set and switch multilevel commands sent to associated devices in the appropriate association group. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 99 | custom brightness level |
| 255 | ON |
Parameter 156: Double Click ON Trigger for Associated Devices
Set the status or brightness level triggering other associated devices in your network if the dimmer is turned ON with a double click. Each of the 4 available bytes refers to one channel, starting with IN1 and ending with IN4. This setting applies to basic set and switch multilevel commands sent to associated devices in the appropriate association group. Size: 4 Byte, Default Value: 99
| Setting | Description |
|---|---|
| 0 - 99 | custom brightness level |
| 255 | ON |
Parameter 157: Preset Programs
Enable one of the preset animated color programs to set the mood with a click. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | preset programs disabled (default) |
| 6 | fireplace |
| 7 | storm |
| 8 | rainbow |
| 9 | polar lights |
| 10 | police (strobing red, white, and blue) |
Parameter 20: Switch / Input Type for IN1
Choose the input / switch type you want to connect to the IN1 terminal. Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | analog sensor with no pull-up |
| 1 | analog sensor with pull-up |
| 2 | momentary switch (default) |
| 3 | toggle switch (state changes whenever the switch is toggled) |
| 4 | toggle switch (light on when the switch is toggled up, light off when the switch is toggled down) |
Parameter 21: Switch / Input Type for IN2
Choose the input / switch type you want to connect to the IN2 terminal. Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | analog sensor with no pull-up |
| 1 | analog sensor with pull-up |
| 2 | momentary switch (default) |
| 3 | toggle switch (state changes whenever the switch is toggled) |
| 4 | toggle switch (light on when the switch is toggled up, light off when the switch is toggled down) |
Parameter 22: Switch / Input Type for IN3
Choose the input / switch type you want to connect to the IN3 terminal. Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | analog sensor with no pull-up |
| 1 | analog sensor with pull-up |
| 2 | momentary switch (default) |
| 3 | toggle switch (state changes whenever the switch is toggled) |
| 4 | toggle switch (light on when the switch is toggled up, light off when the switch is toggled down) |
Parameter 23: Switch / Input Type for IN4
Choose the input / switch type you want to connect to the IN4 terminal. Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | analog sensor with no pull-up |
| 1 | analog sensor with pull-up |
| 2 | momentary switch (default) |
| 3 | toggle switch (state changes whenever the switch is toggled) |
| 4 | toggle switch (light on when the switch is toggled up, light off when the switch is toggled down) |
Parameter 40: Scene Control for IN1
Assign scene activation trigger for IN1 terminal. Enter the sum of values to enable more than 1 trigger. Size: 1 Byte, Default Value: 15
| Setting | Description |
|---|---|
| 0 | scene control disabled |
| 1 | click / toggle the connected switch once to trigger a scene |
| 2 | click / toggle the connected switch twice to trigger a scene |
| 4 | click / toggle the connected switch 3 times to trigger a scene |
| 8 | hold and release the connected momentary switch to trigger a scene |
Parameter 41: Scene Control for IN2
Assign scene activation trigger for IN2 terminal. Enter the sum of values to enable more than 1 trigger. Size: 1 Byte, Default Value: 15
| Setting | Description |
|---|---|
| 0 | scene control disabled |
| 1 | click / toggle the connected switch once to trigger a scene |
| 2 | click / toggle the connected switch twice to trigger a scene |
| 4 | click / toggle the connected switch 3 times to trigger a scene |
| 8 | hold and release the connected momentary switch to trigger a scene |
Parameter 42: Scene Control for IN3
Assign scene activation trigger for IN3 terminal. Enter the sum of values to enable more than 1 trigger. Size: 1 Byte, Default Value: 15
| Setting | Description |
|---|---|
| 0 | scene control disabled |
| 1 | click / toggle the connected switch once to trigger a scene |
| 2 | click / toggle the connected switch twice to trigger a scene |
| 4 | click / toggle the connected switch 3 times to trigger a scene |
| 8 | hold and release the connected momentary switch to trigger a scene |
Parameter 43: Scene Control for IN4
Assign scene activation trigger for IN4 terminal. Enter the sum of values to enable more than 1 trigger. Size: 1 Byte, Default Value: 15
| Setting | Description |
|---|---|
| 0 | scene control disabled |
| 1 | click / toggle the connected switch once to trigger a scene |
| 2 | click / toggle the connected switch twice to trigger a scene |
| 4 | click / toggle the connected switch 3 times to trigger a scene |
| 8 | hold and release the connected momentary switch to trigger a scene |
Parameter 62: Power Report Frequency
Choose howoften you want your RGBW Dimmer to report power consumption (W) to yourcontroller. The number entered as value corresponds to the number of seconds. So if 3600 is entered by default, the RGBW Dimmer will report power consumption every hour. Power reports are sent in at least 30-second intervals. Size: 2 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 0 | disabled (it will not report power consumption based on the fre- quency setting) |
| 30 - 32400 | seconds |
Parameter 63: Analog Sensor Voltage Reporting / Trigger Threshold
Choose how you want your RGBW Dimmer to report voltage changes from the connected analog sensors and trigger status change on the output. The number entered as value corresponds to decimal values in voltage change. So if 5 is entered by default, the RGBW Dimmer will report any change in voltage of the connected sensor over 0.5 V. This setting is only in effect if at least one of Parameters 2023 is set to value 0 or 1 (input is set to analog sensor mode). Size: 2 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | disabled (it will not report voltage based on value change) |
| 1 - 100 | 0.110 V |
Parameter 64: Analog Sensor Report Frequency
Choose howoften you want your RGBW Dimmer to report voltage changes from the connected analog sensors to your hub. The number entered as value corresponds to the number of seconds. So if 3600 is entered as value, the RGBW Dimmer will report voltage from connected analog sensors every hour (independent of the threshold set in parameter 63). Voltage reports are sent in at least 30-second intervals. This setting is only in effect if at least one of Parameters 2023 is set to value 0 or 1 (input is set to analog sensor mode). Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | disabled (it will not report voltage based on the frequency setting) |
| 30 - 32400 | seconds |
Parameter 65: Energy Report Threshold
Choose how you want your RGBW Dimmer to report energy use (kWh) to your hub. The number entered as value corresponds to decimal values in energy usage change. So if 10 is entered by default, the RGBW Dimmer will report any change in energy use over 0.1 kWh. Energy reports are sent in at least 30-second intervals. Size: 2 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | disabled (it will not report energy use based on value change) |
| 1 - 500 | 0.01 - 5 kWh |
Parameter 66: Energy Report Frequency
Choose howoften you want your RGBW Dimmer to report energy (kWh) to your controller. The number entered as value corresponds to the number of seconds. So if 3600 is entered by default, the RGBW Dimmer will report energy use every hour (independent of the threshold set in parameter 65). Energy reports are sent in at least 30-second intervals. Size: 2 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 0 | disabled (it will not report energy use based on the frequency setting) |
| 30 - 32400 | seconds |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Multilevel Switch - Color Tunable Multilevel |
| Network Operation | Always On Slave |
| Firmware Version | HW: 2 FW: 5.00:05.00:01.00 |
| Z-Wave Version | 6.81.03 |
| Certification ID | ZC10-19126818 |
| Z-Wave Product Id | 0x027A.0x0902.0x2000 |
| Z-Wave Scene Type | Central Scene |
| Color | Black |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |