Ring
Contact Sensor
SKU: Contact Sensor v2
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Ring Alarm Contact Sensor is a wireless sensor for the Ring Alarm system which provides users the ability to know when a door or window is open or closed. After installing the sensor on a door or window and setting up the sensor in the Ring app, monitor and receive notifications when the door or window opens or closes. The Ring Alarm Base Station is required to enable Contact Sensor features and functions within the Ring app.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | This is the Lifeline group and the following are the supported Command Classes-1.Notification Reporta.See notification CC section for notifications that are sent2.Battery Report3.Device Reset Locally Notification |
Configuration Parameters
Parameter 1: Heartbeat Interval
Heartbeats are automatic battery reports on a timer after the last event. Size: 1 Byte, Default Value: 70
| Setting | Description |
|---|---|
| 1 - 70 | This parameter is the number of minutes between heartbeats. |
Parameter 2: Application Retriess
Number of application level retries attempted for messages either not ACKed or messages encapsulated via supervision get that did not receive a report. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 5 | This parameter is the number of application level retries. |
Parameter 3: Application Level Retry Base Wait Time Period
The number base seconds used in the calculation for sleeping between retry messages. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 1 - 96 | This parameter is the number base seconds used in the calculation for sleeping between retry messages. |
Parameter 4: LED Indicator Enable
This parameter allows a user, via software, to configure the various LED indications on the device.0 == Don't show green1 == Show green after Supervision Report Intrusion (Fault)2 == Show green after Supervision Report both Intrusion and Intrusion clear Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 2 | This parameter is used to configure the various LED indications on the device. |
Parameter 5: One Shot Timer
Writing to this parameter prompts the sensor to send a wakeup notification one time after this parameter's number of seconds. After which it is reset back to 0. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 5 - 65535 | This parameter prompts the sensor to send a wakeup notification. |
Parameter 6: Supervisory Report Timeout
The number of milliseconds waiting for a Supervisory Report response to a Supervisory Get encapsulated command from the sensor before attempting a retry. Size: 2 Byte, Default Value: 1500
| Setting | Description |
|---|---|
| 500 - 5000 | This parameter is the number of milliseconds waiting for a Supervisory Report response to a Supervisory Get. |
Technical Data
| Hardware Platform | EFR32Z |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.10 |
| Z-Wave Version | 7.12.2 |
| Certification ID | ZC12-20050058 |
| Z-Wave Product Id | 0x0346.0x0201.0x0301 |
| Color | White |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |