This is a
PRODUCT HIGHLIGHTS:- Manual or Z-Wave on/off and brightness control- NEW: 700 series Z-Wave chip for better range and faster control- Simple Direct 3-Way: connect with existing on/off switches in 3-way, 4-way, and 5-way set-ups, no add-on needed- Scene control: trigger actions with multi-tap (select hubs only)- Smart bulb mode: disable relay and control the light via Z-Wave- Night light mode: press down when off to turn lights on to 20%- Adjustable LED indicator in 4 colors and 3 brightness levels- Works with LED and incandescent bulbs (dont use with tubes)SPECS:- Model Number: ZEN77 VER. 1.0- Z-Wave Signal Frequency: 908.42 MHz- Power: 120 VAC, 60 Hz- Maximum Load: 100 W LED, 300 W incandescent; DONT use with fans or tube lights- Range: Up to 500 feet line of sight - Operating Temperature: 32-104 F (0-40 C)- Installation and Use: Indoor only
Reset to factory default | XXXResetDescription |
Inclusion | XXXInclusionDescription |
Exclusion | XXXExclusionDescription |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Lifeline Communication to the hub. |
2 | 5 | Basic set to Group 2. |
3 | 5 | Switch multilevel to Group 3. |
Choose if you want the upper paddle to turn the light on or turn the light off when tapped. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Upper paddle turns the light on, lower paddle turns it off (default) |
1 | Upper paddle turns the light off, lower paddle turns it on |
2 | Any paddle turns light on/off |
Set the minimum brightness level (in %) for your dimmer. You wont be able to dim the light below the set value. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | % brightness |
Set the maximum brightness level (in %) for your dimmer. You wont be able to add brightness to the light beyond the set value. Note: if Parameter 12 is set to value 0, Parameter 11 is automatically disabled. Size: 1 Byte, Default Value: 99
Setting | Description |
---|---|
1 - 99 | % brightness |
Choose what you'd like the dimmer to do when you double-tap the upper paddle. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | the light will turn on to full brightness (default) |
1 | the light will turn on to the custom brightness level set in parameter 18 |
2 | the light will turn on to the maximum brightness level set in Parameter 11 |
3 | double tap disabled |
Enable or disable paddle on/off control (aka disable the relay). If disabled, youll only be able to control the connected light via Z-Wave. Scenes and other functionality will still be available through paddles. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | physical paddle control disabled. |
1 | physical paddle control enabled (default) |
2 | physical paddle and Z-Wave control disabled |
Set the time it takes to get from 0% to 100% brightness when pressing and holding the paddle (physical dimming). The number entered as value corresponds to the number of seconds. Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
1 - 99 | seconds |
Set the custom brightness level (instead of the last set brightness level) you want the dimmer to come on to when you single tap or double tap the upper paddle (see parameters 12 and 25). Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | last brightness level |
1 - 99 | % for custom brightness level |
Choose if you want the LED indicator to turn on when the switch (light) is on or off, or if you want it to remain on or off at all times. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | LED indicator is on when switch is off, LED indicator is off when switch is on (default) |
1 | LED indicator is on when switch is on, LED indicator is off when switch is off |
2 | LED indicator is always OFF |
3 | LED indicator is always ON |
Choose how you'd like the dimmer to report when paddles are tapped and held and physical / Z-Wave control is enabled or disabled. Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | send basic set report for each brightness level to hub when physical / Z-Wave control is disabled for physical dimming when paddles are manually pressed / held; report final brightness level only (basic set report) for physical dimming when paddles are manually pressed / held and physical / Z-Wave control is enabled; always report final brightness level only (via multilevel reports) for Z-Wave control regardless of the physical / Z-Wave control mode. |
1 | report final brightness level only for physical dimming, regardless of the physical / Z-Wave control mode. |
2 | send multilevel report for each brightness level to hub when physical / Z-Wave control is disabled for physical dimming when paddles are manually pressed / held; report final brightness level only (multilevel report) for physical dimming when paddles are manually pressed / held and physical / Z-Wave control is enabled; always report final brightness level only (via multilevel reports) for Z-Wave control regardless of the physical / Z-Wave control mode |
Set reporting behavior for disabled physical control. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | switch reports on/off status and changes LED indicator state even if physical and Z-Wave control is disabled (default) |
1 | switch doesn't report on/off status or change LED indicator state when physical (and Z-Wave) control is disabled. |
Set the brightness level the dimmer will turn on to when off and when lower paddle is held DOWN for a second. Size: 1 Byte, Default Value: 20
Setting | Description |
---|---|
0 | disabled |
1 - 99 | % for custom brightness level |
Choose the color of the LED indicator. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | white |
1 | blue |
2 | green |
3 | red |
Choose the LED indicator's brightness level. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | bright (100%) |
1 | medium (60%) |
2 | low (30%) |
Choose what you'd like the dimmer to do when you tap the upper paddle once. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | the light will turn on to the last brightness level (default) |
1 | the light will turn on to the custom brightness level set in parameter 18 |
2 | the light will turn on to the maximum brightness level set in Parameter 11 |
3 | the light will turn on to full brightness |
Use this parameter to enable or disable the auto turn-off timer function (the time after which you want the switch to automatically turn off once it has been turned on). Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | timer disabled |
1 - 65535 | minutes |
Use this parameter to enable or disable the auto turn-on timer function (the time after which you want the switch to automatically turn on once it has been turned off). Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | timer disabled |
1 - 65535 | minutes |
Set the on off status for the switch after power failure. Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | forced to OFF (regardless of state prior to power outage) |
1 | forced to ON (regardless of state prior to power outage) |
2 | remembers and restores on/off status after power failure (default) |
Adjust the ramp rate for your dimmer (fade-in / fade-out effect for on / off operation). Values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated manually. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | seconds |
Hardware Platform | ZGM130 |
Device Type | Multilevel Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.00 |
Z-Wave Version | 7.13.6 |
Certification ID | ZC12-21030189 |
Z-Wave Product Id | 0x027A.0x7000.0xA007 |
Color | White |
Z-Wave Scene Type | Central Scene |
Electric Load Type | Dimmable LEDELV (Electronic)Incandescent |
Neutral Wire Required | ok |
Firmware Updatable | Updatable by Consumer by RF |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |