Aeotec
MultiSensor 7
SKU: ZWA024-A
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Aeotec MultiSensor 7 is aZ-Wave smart sensor. The corner of your room just got 6 times smarter. Its a motion sensor and its also so much more. Installing this 1 piece of Z-Wave technology is the same as installing 6 pieces of Z-Wave technology. Your home control network will immediately understand motion, temperature, humidity,light, Ultraviolet and Vibration readings wherever MultiSensor 6 is installed. Those intelligent readings will equate to intelligent automation. And intelligent automation will give you the perfect smart home.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Lifeline. Device Reset Locally: When factory reset.Notification Report:See Notification Chapter for more information.Sensor Binary Report:See Param5 for more information.Sensor Multilevel Report:When sensors above over limit or below under limit.Battery Report:See Param101.Indicator Report:Issued when the indicator light changed |
| 2 | 5 | Basic Set Command will be sent to the associated device when motion trigger or untrigger. The basic set value is determined by Param11, Param12. See Param13 for more information. |
| 3 | 5 | Basic Set:When the temperature change value is over or under the threshold set by Param16. Scale is determined by Param64. |
| 4 | 5 | Basic Set:When the temperature change value is under or over the threshold set by Param17. Scale is determined by Param64. |
| 5 | 5 | Basic Set:When the current humidity is over or under the threshold set by Param14 |
| 6 | 5 | Basic Set:When the current humidity is under or over the threshold set by Param15 |
| 7 | 5 | Basic Set:When the current light/lux is over or under the threshold set by Param18 |
| 8 | 5 | Basic Set:When the current light/lux is under or over the threshold set by Param19. |
| 9 | 5 | Basic Set:When the current UV is over or under the threshold set by Param20 |
| 10 | 5 | Basic Set:When the current UV is under or over the threshold set by Param21 |
| 11 | 5 | Sensor Multilevel Report:When sensors above over limit or below under limit. |
Configuration Parameters
Parameter 1: Beaming Enable/Disable
Used to enable/disable beaming.If set to 1, FLiR commands will be supported. But the device must be re-included into the network to activate it.0 - disable1 - enable Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 - 0 | Enable |
Parameter 10: Power Status
This value is Readonly. Used to report the power status (USB or Battery powered)0 - When battery powered, the device will act as RSS.1 - When USB cable insert, the device will act as LSS.The device must be re-included in the network to change the role type. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | When battery powered, the device will act as RSS. |
| 1 - 0 | When USB cable insert, the device will act as LSS. |
Parameter 101: Automatic Report Checklist 1
Checklist 1 for automatic timed report. When the corresponding item is selected, it will be checked when timeout setting by Param111. 1 - Battery16 - UV32 - Temperature64 - Humidity128 - Lux Size: 1 Byte, Default Value: 241
| Setting | Description |
|---|---|
| 1 - 0 | Battery |
| 16 - 0 | UV |
| 32 - 0 | Temperature |
| 64 - 0 | Humidity |
| 128 - 0 | Lux |
Parameter 102: Automatic Report Checklist 2
Checklist 2 for automatic timed report. When the corresponding item is selected, it will be checked when timeout setting by Param112.1 - Battery16 - 32 - Temperature64 - Humidity128 - Lux Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 - 0 | Battery |
| 16 - 0 | UV. Other value descriptions, please see above description box of this parameter. |
Parameter 103: Automatic Report Checklist 3
Checklist 3 for automatic timed report. When the corresponding item is selected, it will be checked when timeout setting by Param113. 1 - Battery16 - UV32 - Temperature64 - Humidity128 - Lux Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 - 0 | Battery. Other value descriptions, please see above description box of this parameter. |
Parameter 11: Motion Group Control(Group2)
Set control of other devices on group2 based on motion trigger.0 - Send BASIC_SET (0xFF) when motion is triggered to associated deviceSend BASIC_SET (0x00) when motion is untriggered to associated device1 - Send BASIC_SET (0x00) when motion is triggeredSend BASIC_SET (0xFF) when motion is untriggered2 - Send BASIC_SET (0xFF) when motion is triggered, Nothing when motion untriggered.3 - Send BASIC_SET (0x00) when motion is triggered, Nothing when motion untriggered.4 - Send BASIC_SET (0x00) when motion is untriggered, Nothing when motion triggered.5 - Send BASIC_SET (0xFF) when motion is untriggered, Nothing when motion triggered.6 - Send BASIC_SET (value is configured by parameter 12) when motion is triggered to associated devices.Send BASIC_SET (value is configured by parameter 12) when motion is untriggered. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Send BASIC_SET (0xFF) when motion is triggered to associated device Send BASIC_SET (0x00) when motion is untriggered to associated device |
| 1 - 0 | Send BASIC_SET (0x00) when motion is triggered Send BASIC_SET (0xFF) when motion is untriggered |
| 2 - 0 | Send BASIC_SET (0xFF) when motion is triggered, Nothing when motion untriggered. |
| 3 - 0 | Send BASIC_SET (0x00) when motion is triggered, Nothing when motion untriggered. |
| 4 - 0 | Send BASIC_SET (0x00) when motion is untriggered, Nothing when motion triggered. |
| 5 - 0 | Send BASIC_SET (0xFF) when motion is untriggered, Nothing when motion triggered. |
| 6 - 0 | Send BASIC_SET (value is configured by parameter 12) when motion is triggered to associated devices. Send BASIC_SET (value is configured by parameter 12) when motion is untriggered. |
Parameter 111: Automatic Checklist 1 Interval Time
Interval time set in seconds to check the checklist1s items. Multilevel Sensor Report will be sent when timeout. Size: 2 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 30 - 65535 | Interval time set in seconds |
Parameter 112: Automatic Checklist 2 Interval Time
Interval time set in seconds to check the checklist2s items. Multilevel Sensor Report will be sent when timeout. Size: 2 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 30 - 65535 | Interval time set in seconds |
Parameter 113: Automatic Checklist 3 Interval Time
Interval time set in seconds to check the checklist3s items. Multilevel Sensor Report will be sent when timeout. Size: 2 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 30 - 65535 | Interval time set in seconds |
Parameter 12: Motion Group Value Setting
Set Basic Set value for Group2. The MSB will act as the basic set value when motion trigger. The LSB will act as the basic set value when motion untrigger. E.g. value=0x0A00, then BASIC_SET(0x0A) will be sent when motion trigger, BASIC_SET(0x00) will be sent when motion untrigger. Size: 2 Byte, Default Value: 65280
| Setting | Description |
|---|---|
| 0 - 65535 | Set Basic Set value for Group2. |
Parameter 13: Motion Group Control Requirement
Set threshold of Light/Lux when devices associated in group2 should be triggered by motion. Associated device only receive BASIC_SET command when light Size: 2 Byte, Default Value: 30000
| Setting | Description |
|---|---|
| 0 - 30000 | Set threshold of Light/Lux |
Parameter 14: Over Humidity Group Threshold (Group5)
Set threshold of humidity. If measured humidity >= (this value), send BASIC_SET (0xFF) to associated devices through group5. If measured humidity < (this value) send BASIC_SET (0x00) to associated devices through group5. Size: 1 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 0 - 100 | Set threshold of humidity. |
Parameter 15: Under Humidity Group Threshold (Group6)
Set threshold of humidity. If measure humidity(this value) send BASIC_SET (0x00) to associated devices through group6. Size: 1 Byte, Default Value: 40
| Setting | Description |
|---|---|
| 0 - 100 | Set threshold of humidity. |
Parameter 16: Over Heat Group Threshold (Group3)
Set threshold of temperature. Designed to control Air Conditioners or temperature controllers ON or OFF. If measuredtemperature >= (this value, Scale is determined by Param64) send BASIC_SET (0xFF) to associated devices. If measured temperature<(this value) send BASIC_SET (0x00) to associated devices. E.g. Value 239 means 23.9 C. Value 750 means 75.0 F. Size: 2 Byte, Default Value: 239
| Setting | Description |
|---|---|
| -400 - 850 | Set threshold of temperature |
Parameter 17: Under Heat Group Threshold (Group4)
Set threshold of temperature. Designed to control Air Conditioners or temperature controllers ON or OFF. If measured temperature(this value) send BASIC_SET (0x00) to associated devices. E.g. Value 155 means 15.5 C. Value 600 means 60.0 F. Size: 2 Byte, Default Value: 155
| Setting | Description |
|---|---|
| -400 - 850 | Set threshold of temperature |
Parameter 18: Over Light Group Threshold (Group7)
Set threshold of Light/Lux. If measured light/lux >= (this value) send BASIC_SET (0xFF) to associated devices. If measured light/lux < (this value) send BASIC_SET (0x00) to associated devices. Size: 2 Byte, Default Value: 2000
| Setting | Description |
|---|---|
| 0 - 30000 | Set threshold of Light/Lux. |
Parameter 19: Under Light Group Threshold (Group8)
Set threshold of Light/Lux. If measured light/lux(this value) send BASIC_SET (0x00) to associated devices. Size: 2 Byte, Default Value: 100
| Setting | Description |
|---|---|
| 0 - 30000 | Set threshold of Light/Lux. |
Parameter 2: Motion Retrigger Time
Presence re-detection time set in second to allow motion sensor to reset timeout of motion sensor. In this time, the motion sensor can not be triggered again. If this value reach zero, the timeout configuration value set by Param3 will be reset. This setting value must always be less than timeout configuration.0 - disable1~3600 - timeout set in seconds Size: 2 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 30 - 3600 | timeout set in seconds |
Parameter 20: Over UV Group Threshold (Group9)
Set threshold of UV. If measured UV >= (this value) send BASIC_SET (0xFF) to associated devices. If measured UV < (this value) send BASIC_SET (0x00) to associated devices. Size: 1 Byte, Default Value: 8
| Setting | Description |
|---|---|
| 0 | Set threshold of UV. |
Parameter 201: Temperature Offset Value
Can add or minus this setting value to calibrate temperature when checked. Scale is defined by Param64. e.g. Value 15 means 1.5C or 1.5F. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -200 - 200 | Temperature Offset Value |
Parameter 202: Humidity Offset Value
Can add or minus this setting value to calibrate humidity when checked. Unit: %. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -100 - 100 | Humidity Offset Value |
Parameter 203: Lux Offset Value
Can add or minus this setting value to calibrate Lux when checked. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -10000 - 10000 | Lux Offset Value |
Parameter 204: UV Offset Value
Can add or minus this setting value to calibrate UV when checked. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -10 - 10 | Offset Value range -10-10. |
Parameter 21: Under UV Group Threshold (Group10)
Set threshold of UV. If measured UV(this value) send BASIC_SET (0x00 to associated devices.) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 11 | Set threshold of UV. |
Parameter 3: Motion Untrigger Time
Timeout configuration set in second for motion sensor to send no trigger status. Size: 2 Byte, Default Value: 240
| Setting | Description |
|---|---|
| 30 - 3600 | timeout set in seconds |
Parameter 39: Low Battery Threshold
Configure low battery report threshold, sends low battery report via notification and battery report when battery level drops under setting. Unit %. Size: 1 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 10 - 90 | Configure low battery report threshold |
Parameter 4: Motion Sensitivity
Set the sensitivity of motion sensor.0 - disable1- minimum sensitivity11 - maximum sensitivity Size: 1 Byte, Default Value: 11
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 - 11 | sensitivity range |
Parameter 40: Threshold Check Enable/Disable
Enable/Disable threshold reporting, check time can be adjusted by Param45.0 - disable all threshold reports1 - enable all threshold reports Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | disable all threshold reports |
| 1 - 0 | enable all threshold reports |
Parameter 41: Temperature Threshold
Threshold = (Value * 0.1) Scale is determined by Param64. 0 = disable. Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 255 | Threshold = (Value * 0.1) Scale is determined by Param64. 0 = disable. |
Parameter 42: Humidity Threshold
Humidity range = 1% to 50%, 0 = disable. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 - 50 | Humidity range = 1% to 50%, 0 = disable. |
Parameter 43: Lux Threshold
0 = disable Size: 2 Byte, Default Value: 250
| Setting | Description |
|---|---|
| 0 - 10000 | Lux Threshold |
Parameter 44: UV Threshold
0 = disable Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 11 | UV Threshold |
Parameter 45: Threshold Check Time
Set threshold check time in seconds if threshold is enable via Param40.1~65535 - When USB powered60~65535 - When Battery powered Size: 2 Byte, Default Value: 240
| Setting | Description |
|---|---|
| 1 - 65535 | Set threshold check time in seconds |
Parameter 46: Low Temperature Report
Eable/Disable alarm report for low temperature( Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 - 0 | Enable |
Parameter 48: Sensor Limit Control
This value is bit mask. Used to enable/disable measurement reports for various sensors that is more than the upper limit value or less than the lower limit value.1 - Temperature upper level2 - Humidity upper level4 - Lux upper level8 - UV upper level16 - Temperature lower level32 - Humidity lower level64 - Lux lower level128 - UV lower level Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 - 0 | Temperature upper level |
| 2 - 0 | Humidity upper level |
Parameter 49: Temperature Upper Limit
Set upper limit level for temperature set in scale of 0.1. Scale is determined by Param64. If (Current measurement) > (Upper Limit), then report sensor. Size: 2 Byte, Default Value: 280
| Setting | Description |
|---|---|
| -400 - 1000 | Set upper limit level for temperature |
Parameter 5: Motion Report Type
Set which command class will be sent when motion sensor is triggered or detriggered.0 - Sends Notification Report1 - Sends Sensor Binary Report2 - Sends Notification and Sensor Binary Report Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | Sends Notification Report |
| 1 - 0 | Sends Sensor Binary Report |
| 2 - 0 | Sends Notification and Sensor Binary Report |
Parameter 50: Temperature Lower Limit
Set lower limit level for temperature set in scale of 0.1. Scale is determined by Param64. If (Current Measurement) < (Lower limit), then report sensor. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -400 - 1000 | Set lower limit level for temperature |
Parameter 51: Temperature Recover Limit
Temperature recover limit set in scale of 0.1. Scale is determined by Param64. If (Current measurement) = (lower limit + recover limit), then temperature report. Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 1 - 255 | Temperature recover limit set in scale of 0.1. |
Parameter 52: Humidity Upper Limit
Set humidity upper limit level. Size: 1 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 0 - 100 | Set humidity upper limit level. |
Parameter 53: Humidity Lower Limit
Set humidity lower limit level Size: 1 Byte, Default Value: 40
| Setting | Description |
|---|---|
| 0 - 100 | Set humidity lower limit level |
Parameter 54: Humidity Recover Limit
Set humidity recover limit level. Refer to Param 51. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 1 - 50 | Set humidity recover limit level |
Parameter 55: Lux Upper Limit
Set lux upper limit level. Size: 2 Byte, Default Value: 1000
| Setting | Description |
|---|---|
| 0 - 30000 | Set lux upper limit level. |
Parameter 56: Lux Lower Limit
Set lux lower limit level. Size: 2 Byte, Default Value: 100
| Setting | Description |
|---|---|
| 0 - 30000 | Set lux lower limit level. |
Parameter 58: UV Upper Limit
Set UV upper limit level. Size: 1 Byte, Default Value: 8
| Setting | Description |
|---|---|
| 1 - 11 | Set UV upper limit level. |
Parameter 59: UV Lower Limit
Set UV lower limit level. Size: 1 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 1 - 11 | Set UV lower limit level. |
Parameter 6: Vibration Sensor Enable/Disable
Used to enable/disable vibration sensor.0 - disable vibration1~254 - timeout set in minutes to reset vibration status255 - timeout set in minutes to reset vibration status Size: 1 Byte, Default Value: 255
| Setting | Description |
|---|---|
| 0 | disable vibration |
| 1 - 254 | timeout set in minutes to reset vibration status |
| 255 | timeout set in minutes to reset vibration status |
Parameter 60: UV Recover Limit
Set UV recover limit level. Refer to Param 51. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 5 | Set UV recover limit level. |
Parameter 61: Out-of-limit State
This is read only and bit mask. Out of the limit state of sensors.Bit Mask:0 - within limit1 - out of limitValue:1 - Temperature upper level2 - Humidity upper level4 - Lux upper level8 - UV upper level16 - Temperature lower level32 - Humidity lower level64 - Lux lower level128 - UV lower level Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | within limit |
| 1 - 0 | Temperature upper level |
| 2 - 0 | Humidity upper level |
| 4 - 0 | Lux upper level |
Parameter 64: Temperature Scale
Set the scale for temperature when reports.0 - Celsius1 - Fahrenheit Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Celsius |
| 1 - 0 | Fahrenheit |
Parameter 67: Lux Recover Limit
Set lux recover limit level. Refer to Param 51. Size: 1 Byte, Default Value: 100
| Setting | Description |
|---|---|
| 1 - 255 | Set lux recover limit level. |
Parameter 7: Vibration Intensity Reports
Used to enable/disable vibration intensity reports. If set to 1, vibration intensity will be sent to gateway when triggered. If set to 0, do not report. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 - 0 | Enable |
Parameter 81: LED Activity
Allow user to enable/disable LED activity of specific reports sent by sensor. Button press indicator is not affected by this.0 - disable1 - enable Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | disable |
| 1 - 0 | enable |
Parameter 82: Motion Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of motion sensor.0 - Disabled1 - Red2 - Blue3 - Green4 - Pink5 - Cyan6 - Purple7 - Orange8 - Yellow9 - White Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 - 0 | Red |
| 2 - 0 | Blue |
| 3 - 0 | Green |
| 4 - 0 | Pink |
| 5 - 0 | Cyan |
| 6 - 0 | Purple |
| 7 - 0 | Orange |
| 8 - 0 | Yellow |
| 9 - 0 | White |
Parameter 83: Temperature Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of temperature sensor.0 - Disabled1 - Red2 - Blue3 - Green4 - Pink5 - Cyan6 - Purple7 - Orange8 - Yellow9 - White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable. Other value descriptions, please see above description box of this parameter. |
Parameter 84: Humidity Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of humidity sensor.0 - Disabled1 - Red2 - Blue3 - Green4 - Pink5 - Cyan6 - Purple7 - Orange8 - Yellow9 - White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable. Other value descriptions, please see above description box of this parameter. |
Parameter 85: Lux Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of Lux sensor.0 - Disabled1 - Red2 - Blue3 - Green4 - Pink5 - Cyan6 - Purple7 - Orange8 - Yellow9 - White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable. Other value descriptions, please see above description box of this parameter. |
Parameter 86: UV Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of UV sensor.0 - Disabled1 - Red2 - Blue3 - Green4 - Pink5 - Cyan6 - Purple7 - Orange8 - Yellow9 - White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable. Other value descriptions, please see above description box of this parameter. |
Parameter 87: Vibration Sensor Report Indicator
If LED is enabled by Param81, allow user to change the report color of vibration sensor.0 - Disabled1 - Red2 - Blue3 - Green4 - Pink5 - Cyan6 - Purple7 - Orange8 - Yellow9 - White Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | Disable. Other value descriptions, please see above description box of this parameter. |
Parameter 88: Battery Report Indicator
If LED is enabled by Param81, allow user to change the report color of battery.0 - Disabled1 - Red2 - Blue3 - Green4 - Pink5 - Cyan6 - Purple7 - Orange8 - Yellow9 - White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable. Other value descriptions, please see above description box of this parameter. |
Parameter 89: Wakeup Report Indicator
If LED is enabled by Param81, allow user to change the report color of wakeup.0 - Disabled1 - Red2 - Blue3 - Green4 - Pink5 - Cyan6 - Purple7 - Orange8 - Yellow9 - White Size: 1 Byte, Default Value: 8
| Setting | Description |
|---|---|
| 0 | Disable. Other value descriptions, please see above description box of this parameter. |
Parameter 9: Wakeup CC Timeout
Timeout set in seconds after Wakeup CC is send out before go to sleep. If wakeup no more information received, return to sleep mode immediately. Size: 1 Byte, Default Value: 15
| Setting | Description |
|---|---|
| 0 - 255 | Timeout set in seconds |
Parameter 90: Communication Indicator
If LED is enabled by Param81, allow user to change indicator color when receiving communication from gateway or other devices.0 - Disabled1 - Red2 - Blue3 - Green4 - Pink5 - Cyan6 - Purple7 - Orange8 - Yellow9 - White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable. Other value descriptions, please see above description box of this parameter. |
Technical Data
| Hardware Platform | ZGM130 |
| Device Type | Notification Sensor |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.01 |
| Z-Wave Version | 7.12.2 |
| Certification ID | ZC12-21080291 |
| Z-Wave Product Id | 0x0371.0x0102.0x0018 |
| Color | White |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |