Ness
Ness Z-Wave Door Strike Controller
SKU: ZA-116001
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Ness Z-Wave Door Lock Controller (DLC) is a unique access control accessory providing a smart relay output and door position sensor inputs.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 |
Configuration Parameters
Parameter 1: The Relock Timer
Sets the output duration for the RELAY Output and the 12V Lock Output. Output ON duration in seconds. Range: 0 ~ 300. Default value: 10. 0 = Latching Operation. Size: 2 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 2: Function Options for Input Terminal SW1
Range: 0 ~ 3. Default: 2. Value = 0: The input is disabled. Value = 1: Normally Closed Door sensor. Value = 2: Normally Open Door sensor. Value = 3: External unlock pushbutton input (close circuit to unlock) Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 3: Function Options for Input Terminal SW2
Range: 0 ~ 3. Default: 3. Value = 0: The input is disabled. Value = 1: Normally Closed Door sensor. Value = 2: Normally Open Door sensor. Value = 3: External unlock pushbutton input (close circuit to unlock) Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 4: Battery Low setting
Reporting the battery low warning message when battery level reaches this value in percentage. Range: 10 ~ 50 (10% to 50%). Default: 10% Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 5: Battery Scheduled Report Interval
The battery level scheduled report interval time is based on every 30 minutes per kick. The value N related to the time in minutes is N x 30 minutes. Range: 0~120. Default: 12 (12x30 =360 minutes). Value = 0: Disable Battery level scheduled report. Size: 1 Byte, Default Value: 12
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 6: The 12V DC Power Output Options
This parameter is used to enable/disable the 12V CD power output at the power output terminal. Range: 0~1. Default: 0. Value = 0: The power output is disabled; Value = 1: The power output is enabled. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Technical Data
| Hardware Platform | ZGM130S037HGN2 / ZGM130S037HGN1 |
| Device Type | Lock DT |
| Network Operation | Listening Sleeping Slave |
| Firmware Version | HW: 01 FW: 01.03 |
| Z-Wave Version | 7.15.4 |
| Certification ID | ZC14-22020058 |
| Color | White |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |