Aeotec
Outdoor Smart Plug
SKU: ZWA042
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Aeotec Z-Wave Outdoor Smart Plug
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 0 |
Configuration Parameters
Parameter 1: Reaction of led
Parameter setting to change the reaction of LEDsetting. Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 2: Night led on time
Night Light ON time. Size: 4 Byte, Default Value: 1572864
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 3: Night led off time
Night Light OFF time. Size: 4 Byte, Default Value: 393216
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 30: Alarm setting
Determines if alarms are enabled in Switch, and whatSwitch will react to which alarms. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 31: Alarm response in device
Enabled by (Alarm settings), and determines what theswitch does in the case an alarm is triggered. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 32: Alarm disable setting
Determines the method of disabling the alarm of thedevice. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 4: Indicator play duration
Setting indicator play duration. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 40: Auto turn off timer
Auto off after as soon as the switch turns ON Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 41: Auto turn on timer
Auto on after as soon as the switch turns OFF Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 5: Indicator speed
Select indicator flash speed. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 7: Control turn off
Prevents the plug from being turned off via its button. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 8: Restore status after power failure
Action in case of power out. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Technical Data
| Hardware Platform | ZGM130S037HGN2 / ZGM130S037HGN1 |
| Device Type | Binary Switch DT |
| Network Operation | Always On Slave |
| Firmware Version | HW: 01 FW: 01.00 |
| Z-Wave Version | 7.16.3 |
| Certification ID | ZC14-22050107 |
| Z-Wave Scene Type | Scene |
| Electric Load Type | Dimmable LEDELV (Electronic)IncandescentInductive (e.g. Motor)LEDMLV (Magnetic) |
| Outdoor Use | ok |
| Switch Type | Toggle |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |