Jasco Products Company
Plug-in Smart Dimmer, Dual Outlet with Simultaneous Control
SKU: 14307
Quickstart
This is a
1. Follow the instructions for your Z-wave certified controller to include the device to the Z-wave network.2. Once the controller is ready to include your smart switch, single press and release the manual/program button on the smart dimmer to include it in the network.3. Once your controller has confirmed that the smart switch has been included, refresh the Z-wave network to optimize performance.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Transform any home into a smart home with the Jasco Z-Wave Smart Lighting Control Lamp Module with Dimmer Control. The lamp module enables wireless control of on/off and dim functions for standard incandescent table and floor lamps, as well as dimmable fluorescent, LED and CFL fixtures and more! Use the dimmer control to customize the lighting output and create the perfect ambiance for any room. The space-saving horizontal module plugs into a standard wall receptacle without blocking the second outlet or obstructing placement of furniture. The Dimmer provides one Z-Wave enabled outlet for the lamp you would like to control. Take control of your home lighting with Jasco Z-Wave Smart Lighting Controls!
| Reset to factory default | 1. If plugged in, unplug the Switch from the receptacle.2. Press and hold the top button for at least 3 seconds while you plug the switch into a receptacle.Note: This should only be used in the event your networks primary controller is missing or otherwise inoperable. |
| Inclusion | 1. Follow the instructions for your Z-wave certified controller to include the device to the Z-wave network.2. Once the controller is ready to include your smart switch, single press and release the manual/program button on the smart dimmer to include it in the network.3. Once your controller has confirmed that the smart switch has been included, refresh the Z-wave network to optimize performance. |
| Exclusion | 1. Follow the instructions for your Z-wave certified controller to exclude a device from the Z-wave network.2. Once the controller is ready to Exclude your device, press and release the manual/program button on the smart switch to exclude it from the network. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 10: Dim Rate Adjustments (When manually controlled)
timing of the steps Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | timing of the steps |
Parameter 11: Dim Rate Adjustments (When receiving All-On/All-Off command)
number of steps or levels Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | number of steps or levels |
Parameter 12: Dim Rate Adjustments (When receiving All-On/All-Off command)
timing of the steps Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | timing of the steps |
Parameter 3: LED Light
To make the LED turn ON when the light is turned ON, change parameter 3s value to 1. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | To make the LED turn ON when the light is turned ON, change parameter 3s value to 1. |
| 2 | To turn the LED OFF at all times, change parameter 3s value to 2 |
Parameter 7: Dim Rate Adjustments (From Z-Wave Controller)
number of steps or levels Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | number of steps or levels |
Parameter 8: Dim Rate Adjustments (From Z-Wave Controller)
timing of the steps Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | timing of the steps |
Parameter 9: Dim Rate Adjustments (When manually Controlled)
number of steps or levels Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | number of steps or levels |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-15070015 |
| Z-Wave Product Id | 0x0063.0x5044.0x3035 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |