Quickstart

This is a Light Dimmer Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
Adding your device to a Z-wave network:1. Follow the instructions for your Z-wave certified controller to include a device tothe Z-wave network.2. Once the controller is ready to include your device, press up and release on thetoggle to include it in the network.3. Once your controller has confirmed that the device has been included, refreshthe Z-wave network to optimize performance.Please reference the controllers manual for instructions.Now you have complete control to turn your fixture ON/OFF or dimaccording to groups, scenes, schedules and interactive automationsprogrammed by your controller.If your Z-wave certified controller features Remote Access, you can now controlyour fixture from your mobile devices.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

Transform any home into a smart home with the Jasco Z-Wave Smart Toggle Dimmer. The in-wall Dimmer can easily replaces any standard in-wall switch remotely controls a light in your home. Your home will be equipped with ultimate flexibility with the Jasco Z-Wave Smart Toggle Dimmer, capable of being used by itself or with up to four add-on switches. Screw terminal installation provides improved space efficiency when replacing existing switches. The Jasco Z-Wave Smart Toggle Dimmer is compatible with any Z-Wave certified gateway, providing access to many popular home automation systems. Take control of your home lighting with Jasco Z-Wave Smart Lighting Controls! Z-Wave is the worlds largest ecosystem of interoperable smart home products. Z-Wave lighting controls provide an easy-to-install and affordable system to control lighting and small appliances in your home. Add GE Z-Wave lighting controls to a Z-Wave certified gateway to access and control your home from anywhere in the world using your smartphone, tablet or computer as a home automation command center. Never worry if you accidentally left the lights on because you can turn them off remotely or program your lights to go on/off at specific times. Create customized lighting scenes for any occasion such as a go to sleep scene or a movie night scene. Give the illusion that someone is home by programming the lights to turn on/off while you are awayperfect for deterring crime and adding additional security!"

Reset to factory default To return your switch to factory defaults:1. Quickly press ON (Up) button three (3) times then immediately press the OFF(Down) button three (3) times. Note: This should only be used in the event yournetworks primary controller is missing or otherwise inoperable.
Inclusion Adding your device to a Z-wave network:1. Follow the instructions for your Z-wave certified controller to include a device tothe Z-wave network.2. Once the controller is ready to include your device, press up and release on thetoggle to include it in the network.3. Once your controller has confirmed that the device has been included, refreshthe Z-wave network to optimize performance.Please reference the controllers manual for instructions.Now you have complete control to turn your fixture ON/OFF or dimaccording to groups, scenes, schedules and interactive automationsprogrammed by your controller.If your Z-wave certified controller features Remote Access, you can now controlyour fixture from your mobile devices.
Exclusion To exclude and reset the device1. Follow the instructions for your Z-wave certified controller to exclude a device fromthe Z-wave network.2. Once the controller is ready to Exclude your device, press up and release on thetoggle to exclude it from the network.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Z-Wave Plus Lifeline

Configuration Parameters

Parameter 10: Dim Rate Adjustments

Dim Rate Adjustments When manually controlling dimmingFor values over 127, consult your controller's user guide; some controllers may require values above 127 to be entered using the 2's complement value or using hexadecimal notation
Size: 1 Byte, Default Value: 3

Setting Description
1 - 255 timing of the steps

Parameter 11: Dim Rate Adjustments

Dim Rate Adjustments When receiving an All-On or All-Off command
Size: 1 Byte, Default Value: 1

Setting Description
1 - 99 number of steps or levels

Parameter 12: Dim Rate Adjustments

Dim Rate Adjustments When receiving an All-On or All-Off commandFor values over 127, consult your controller's user guide; some controllers may require values above 127 to be entered using the 2's complement value or using hexadecimal notation
Size: 1 Byte, Default Value: 3

Setting Description
1 - 255 timing of the steps

Parameter 4: Default

Default
Size: 1 Byte, Default Value: 0

Setting Description
0 Default

Parameter 7: Dim Rate Adjustment

Dim Rate Adjustments When receiving a Z-Wave Dim Command
Size: 1 Byte, Default Value: 1

Setting Description
1 - 99 Number of steps or levels

Parameter 8: Dim Rate Adjustment

Dim Rate Adjustments When receiving a Z-Wave Dim CommandFor values over 127, consult your controller's user guide; some controllers may require values above 127 to be entered using the 2's complement value or using hexadecimal notation
Size: 1 Byte, Default Value: 3

Setting Description
1 - 255 timing of the steps

Parameter 9: Dim Rate Adjustments

Dim Rate Adjustments When receiving a Z-Wave Dim Command
Size: 1 Byte, Default Value: 1

Setting Description
1 - 99 number of steps or levels

Technical Data

Hardware Platform ZM5202
Device Type Light Dimmer Switch
Network Operation Always On Slave
Firmware Version HW: 255
Z-Wave Version 6.51.06
Certification ID ZC10-15060025
Z-Wave Product Id 0x0063.0x4944.0x3137
Frequency XXfrequency
Maximum transmission power XXantenna
U.S. / Canada / MexicoLight Dimmer Switch