This is a
Adding your device to a Z-wave network1. Follow the instructions for your Z-wave certified controller to include a device to the Z-wavenetwork.2. Once the controller is ready to include your device, press and release the top or bottom of thewireless smart switch(rocker) to include it in the network.3. Once your controller has confirmed that the device has been included, refresh the Z-wave networkto optimize performance.Please reference the controllers manual for instructions.Now you have complete control to turn your fixture ON/OFFaccording to groups, scenes, schedulesand interactive automations programmed by your controller.If your Z-wave certified controller features Remote Access, you can now control your fixture fromyour mobile devices.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Transform any home into a smart home with the Jasco Z-Wave Smart Dimmer. The In-Wall Smart Dimmer can easily replace any standard in-wall switch and remotely controls a light in your home. Your home will be equipped with ultimate flexibility with the Jasco Z-Wave Smart Toggle Dimmer, capable of being used by itself or with up to four add-on switches. Screw terminal installation provides improved space efficiency when replacing existing switches and the integrated LED indicator light allows you to easily locate the switch in a dark room. The Jasco Z-Wave In-Wall Smart Dimmer is compatible with any Z-Wave certified gateway, providing access to many popular home automation systems. Take control of your home lighting with Jasco Z-Wave Smart Lighting Controls! Z-Wave is the worlds largest ecosystem of interoperable smart home products. Z-Wave lighting controls provide an easy-to-install and affordable system to control lighting and small appliances in your home. Add GE Z-Wave lighting controls to a Z-Wave certified gateway to access and control your home from anywhere in the world using your smartphone, tablet or computer as a home automation command center. Never worry if you accidentally left the lights on because you can turn them off remotely or program your lights to go on/off at specific times. Create customized lighting scenes for any occasion such as a go to sleep scene or a movie night scene. Give the illusion that someone is home by programming the lights to turn on/off while you are awayperfect for deterring crime and adding additional security!"
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
To return your switch to factory defaults:Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three(3) times. The LED will flash ON/OFF 5 times when completed successfully.Note: This should only be used in the event your networks primary controller ismissing or otherwise inoperable.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Z-Wave Plus Lifeline |
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Dim Rate Adjustments When manually controlling dimming.For values over 127, consult your controller's user guide; some controllers may require values above 127 to be entered using the 2's Complement value or using Hexadecimal notation. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | timing of the steps |
Dim Rate Adjustments When receiving an All-On or All-Off command Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | number of steps or levels |
Dim Rate Adjustments When receiving an All-On or All-Off command. For values over 127, consult your controller's user guide; some controllers may require values above 127 to be entered using the 2's Complement value or using Hexadecimal notation. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | Timing of the steps |
When shipped from the factory, the LED is set to turn ON when the connected light is turned OFF. This is the default setting and can be changed if your primary controller supports the node configuration function. To make the LED turn ON when the light is turned ON, change parameter 3s value to 1. To turn the LED OFF at all times, change parameter 3s value to 2. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
1 | LED light on when on |
2 | LED light at all times |
0 | Default |
If the switch is accidentally installed upside down with On at the bottom and Off at the top, the default On/Off rocker settings can be reversed by changing parameter 4s value to 1. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
1 | Invert |
0 | Default |
number of steps or levels Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | number of steps or levels |
Timing of the steps. For values over 127, consult your controller's user guide; some controllers may require values above 127 to be entered using the 2's Complement value or using Hexadecimal notation. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
1 - 255 | Timing of the steps |
0 | Instant |
number of steps or levels Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | number of steps or levels |
Hardware Platform | ZM5202 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 255 |
Z-Wave Version | 6.51.06 |
Certification ID | ZC10-15060023 |
Z-Wave Product Id | 0x0063.0x4944.0x3136 |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |