Andersen
VeriLock Translator
SKU: 9125051
Quickstart
This is a
If not included to a Z-Wave network, the device will attempt to be added to the network at power-up following an LED start-up sequence.The controller must be put into include mode before plugging in the device.During normal operation, after putting the controller into include mode, a single press of the round Z-Wave button will add the device to the Z-Wave network.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The VeriLock Translator is an indoor device that allows users to monitor the status of over 100 VeriLock sensors by Nexia Home Intelligence using standard Z-Wave interfaces.These sensors are added to the VeriLock Translator as Multi Channel End Points.Because the number of sensors in a home is dynamic, the number of End Points on the device is also dynamic. Unlike the VeriLock Translator, the sensors are NEVER represented as nodes on the Z-Wave network and cannot communicate over the Z-Wave network.Their status, however, is reported by the VeriLock Translator over the Z-Wave network via the Multi Channel Command Class.The VeriLock Translator is added to the Z-Wave network as a Repeater and implements the Routing Slave library.The VeriLock Translator is a Z-Wave Plus certified device.
| Reset to factory default | The device is factory reset by pressing and holding both the round (Z-Wave) and square (Multi-Purpose) buttons simultaneously for 15 seconds.Please use this procedure only in emergencies such as when the network primary controller is missing or otherwise inoperable.This should always be used as a last resort. |
| Inclusion | If not included to a Z-Wave network, the device will attempt to be added to the network at power-up following an LED start-up sequence.The controller must be put into include mode before plugging in the device.During normal operation, after putting the controller into include mode, a single press of the round Z-Wave button will add the device to the Z-Wave network. |
| Exclusion | After putting the controller in exclude mode, a single press of the round Z-Wave button will remove the device from the Z-Wave network. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 1: Buzzer Volume
Adjust the buzzer volume Size: 1 Byte, Default Value: 100
| Setting | Description |
|---|---|
| 0 - 100 | 100 is max volume. 0 is off. |
Parameter 2: Discovery Mode
Start, stop, or get the results of Discovery Mode. Retrieve the configuration parameter to obtain the results of discovery mode:0=Not Enabled, 1=Enabled, 2=Timed Out, 3=Failure Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Enable |
| 0 | Disable |
Parameter 3: Sleep Mode
Turn Sleep Mode ON or OFF. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | OFF |
| 1 | ON |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Repeater |
| Network Operation | Always On Slave |
| Z-Wave Version | 6.51.03 |
| Certification ID | ZC10-14120001 |
| Z-Wave Product Id | 0x0178.0x5A44.0x414E |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |