ABUS
ABUS Z-Wave Smoke detector
SKU: ABUESHRM10000
Quickstart
This is a
A.) Slide the base unit from the mounting plate and remove the safety strip from the battery compartment
B.) Click the + (Add) button in your Z-Wave App and follow the further instructions
C.) Press the Network-button 3 times within 1.5 seconds and the Status-LED on the base unit front will flash 3 times. The App will show if the Add device process was successful and the Status-LED will turn off. Repeat the inclusion process from step B if it was not successful.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
The ABUS Z-Wave Smoke detector provides reliable warning of risk of potentially fatal smoke inhalation and sounds an alarm. Its compact design does not compromise the functionality but even convinces with low maintenance due to 5 years of battery life. The Smoke detector also includes a test button for manual self-testing, for test alarms and temporary muting.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
1. Remove the battery
2. Press the Network button and keep it pressed while inserting the battery again.
3. Device will restore factory settings
Safety Warning for Batteries
The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different brands.
Installation
- Flat ceiling mounting
The preferred location to install smoke sensor is in the centre of the ceiling, because smoke, heat and combusible products rise to ceiling and will laterally spread. Keep at least 30 cm distance from lights or decoration and at least 17cm away from walls and corners.
- Sloping ceiling mounting
If ceiling is sloping, please install the smok sensor at horizontal distance 90 cm away from the ceiling top.
Installation guide
- Anticlockwise rotation the bracket out from the installation base.
- Fixed the bracket intoceiling using srews.
- Remove the double-sided adhersive and stickalarm into ceiling
- Remove the battery insulating strip to make detector on power and clockwise rotating alarm into bracket.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Inclusion
A.) Slide the base unit from the mounting plate and remove the safety strip from the battery compartmentB.) Click the + (Add) button in your Z-Wave App and follow the further instructions
C.) Press the Network-button 3 times within 1.5 seconds and the Status-LED on the base unit front will flash 3 times. The App will show if the Add device process was successful and the Status-LED will turn off. Repeat the inclusion process from step B if it was not successful.
Exclusion
A.) Click the - (Remove) button in your Z-Wave App and follow the further instructions.B.) Press the Network-button 3 times within 1.5 seconds and the Status-LED on the base unit front will flash 3 times. The App will show if the Remove device process was successful and the Status-LED on device will flash 6 times. Repeat the exclusion process from step A if it was not successful.
Product Usage
Node Information Frame
The Node Information Frame (NIF) is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this it may be needed for certain network operations to send out a Node Information Frame. To issue a NIF execute the following action: Press network button once.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Lifeline association group Include command classes: Battery report, Notification report, and Device Reset Locally notification, Binary report. |
| 2 | 5 | Root Device group(Binary Sensor) Binary Sensor Command Class: Compatible with 300 series 1-Binary Sensor reports status of smoke or no smoke via Lifeline. 2-When the sensor detectsstatus change between smoke and no smoke, the device will be triggered. |
| 3 | 5 | Root Device group(Notification) 1-Notification reports) reports the status of detect smoke or no smoke via Lifeline. 2-When the sensor detects status change between smoke and no smoke, the device will be triggered |
Technical Data
| Dimensions | 60 x 50 x 60 mm |
| Weight | 50 gr |
| Hardware Platform | ZM5202 |
| EAN | 4003318841507 |
| IP Class | IP 20 |
| Voltage | 3V |
| Battery Type | 1 * CR17335 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-18096244 |
| Z-Wave Product Id | 0x0403.0x0002.0x0003 |
| Firmware Updatable | Updatable by Manufacturer |
| Color | White |
| Communications Protocol | Z-Wave Serial API |
| Supported Notification Types | Emergency AlarmSmoke Alarm |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |
Supported Command Classes
- Association Grp Info
- Association V2
- Battery
- Device Reset Locally
- Manufacturer Specific V2
- Multi Channel Association V3
- Notification V8
- Powerlevel
- Security 2
- Supervision
- Transport Service V2
- Version V3
- Wake Up V2
- Zwaveplus Info V2
Controlled Command Classes
- Basic V2
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.