This is a
1. Put the Z-Wave Controller into inclusion mode.2. Press the link key three times within 1.5 seconds to put the unit into inclusion mode. (Please refer to the documentation for the location of the link key.)
The mini Dimmer Plug is a Z-Wave enabled device which is fully compatible with any Z-Wave enabled network.Z-Wave enabled devices displaying the Z-Wave logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturers Z-Wave enabled networks.Inclusion of this unit on other manufacturers Wireless Controller menu allows remote operation of the unit and the connected load.The mini Dimmer Plug is designed to control the on/off status of lighting and appliances load in your house.The unit also provides dimmer function which is only applicable to light bulbs.At 220-240V voltage, this Dimmer Plug can support connected load of 6 - 250W.
Reset to factory default | (This procedure should only be used when the network primary controller is inoperable.)1. Press the link key three times within 1.5 seconds to put the unit into exclusion mode.2. Within 1 second of step 1, press link key again and hold it until LED is off (about 5 seconds). (Please refer to the documentation for the location of the link key.)3. Node ID is excluded.The device reverts to factory default state and will be in auto-inclusion mode for 4 minutes. |
Inclusion | 1. Put the Z-Wave Controller into inclusion mode.2. Press the link key three times within 1.5 seconds to put the unit into inclusion mode. (Please refer to the documentation for the location of the link key.) |
Exclusion | 1. Put the Z-Wave Controller into exclusion mode.2. Press the link key three times within 1.5 seconds to put the unit into exclusion mode. (Please refer to the documentation for the location of the link key.) |
NIF | XXXNIF |
Wakeup | NR |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | 1.When the unit is powered for the first time, the unit will send a Notification Report to the node of Group 1.2. When setting the unit or changing the units status, the unit will send a Multilevel Switch Report to the node of Group 1.3. Device Reset: When performing Reset the unit will send Device Reset Locally Notification to the node of Group1.4. The minimum interval time between two reports sent from this unit to the node of Group 1 is 3 seconds.Refer to Configuration parameter 2 for more information. |
2 | 4 | When the button on the unit or the wall switch is pressed, the unit will send a Basic Set command to the nodes of Group 2.When the unit is OFF, Basic Set Value = 0x00.When the unit is ON, Basic Set Value = 0xFF. |
Basic Set Command value.When the device sends a BASIC SET command, the value indicated here will be sent. Size: 2 Byte, Default Value: 255
Setting | Description |
---|
The delaying time to report to Group 1.When a notification is sent to the nodes in Group 1, the send will take place after the delay period indicated with this value. Size: 1 Byte, Default Value: 3
Setting | Description |
---|
Remember the last status of the load.1: remember, 0: do not remember Size: 1 Byte, Default Value: 1
Setting | Description |
---|
Output mode setting: Dimming, On/OffNote: When set to 1, the operation mode is not changed; only the light would be turned on with 100% brightness immediately. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 1 | 0 (Dimmable) or 1 (On/Off) |
Hardware Platform | SD3502 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | 02 |
Z-Wave Version | 6.51.02 |
Certification ID | ZC10-14080010 |
Z-Wave Product Id | 0x0060.0x0003.0x0003 |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |