Quickstart

This is a secure Smart Meter for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
- Push the button on backside



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Installed in an electricity box, the energy meter will monitor the total consumption of electricity used by an entire building. And its intelligent clamps will report that energy use back to your Z-Wave gateway or controller, in watts or kilowatt-hours, and in real time. So you can see how much electricity you really use and when you use it.

Installation

Unless otherwise stated, the circuit box?s main breaker should be turned off to perform these installation steps.

  1. Turn the main breaker off.
  2. Open the main circuit box panel.
  3. Clip one clamp of the meter around the incoming electricity cable that connects to the main circuit breaker.
  4. Connect the clamp to the meter using a Clamp Connector.
  5. Connect the AC Wire to the meter using the AC Wire Connector.
  6. Wire the AC Wire into one breaker. The brown wire is Live, the blue wire is neutral.
  7. Replace the main circuit box panel.
  8. Turn the main breaker back on.

It is now time to place the main body of the Home Energy Meter. Inside the meter is a radio antenna used for communications, and this must be taken into consideration when selecting a location for the meter.
If the circuit boxes is made of metal the radio signal strength may be reduced. In this situation it is recommended that the main body of the meter be affixed outside the circuit box. This will improve the radio signal strength. The Home Energy Meter has been weatherized to the international IP43 standard so that it is resistant to rain and snow when placed vertically with the wires protruding from the bottom of the unit.

To place the Home Energy Meter:

  1. Unslot the backing plate from the back of your meter.
  2. Affix the plate to the selected wall space using the provided screws.
  3. Attach your meter to the backing plate.

Reset to factory default - Press and hold the button on the backside for 10 seconds
Inclusion - Push the button on backside
Exclusion - Push the button three times on backside
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Send configured Value to devices

Configuration Parameters

Parameter 2: Energy detection mode

For parameters of 101, power, energy detection mode
Size: 1 Byte, Default Value: 0

Setting Description
0 report power, energy absolute value
1 report positive/negative power, report the algebraic sum energy
2 report positive/negative power, only report energy positive part (consuming electricity)
3 report positive/negative power, only report energy negative part (generating electricity)

Parameter 3: Selective reporting

Enable selective reporting only when power change reaches a certain threshold or percentage set in 4-11 below. This is used to reduce network traffic.
Size: 1 Byte, Default Value: 1

Setting Description
0 disable
1 enable

Parameter 4: Threshold change in wattage

Threshold change in wattage to induce a automatic report (Whole HEM).
Size: 2 Byte, Default Value: 50

Setting Description
0 - 60000 Watt

Parameter 5: Threshold change in wattage (Clamp 1)

Threshold change in wattage to induce a automatic report
Size: 2 Byte, Default Value: 50

Setting Description
0 - 60000 Watt

Parameter 8: Percentage change in wattage (Whole HEM)


Size: 1 Byte, Default Value: 10

Setting Description
0 - 100 Valid value

Parameter 9: Percentage change in wattage (Clamp 1)

Percentage change in wattage to induce a automatic report
Size: 1 Byte, Default Value: 10

Setting Description
0 - 100 Valid value

Parameter 13: Enable /disable reporting

Enable /disable reporting CRC-16 Encapsulation Command
Size: 1 Byte, Default Value: 0

Setting Description
0 disable
1 enable

Parameter 100: Reset parameter 101


Size: 1 Byte, Default Value: 0

Setting Description
1 reset parameter 101

Parameter 101: Setting automatic report flags Group 1

Example:   1 + 1024 = Value 1025
If you want to report everthing, you would add the whole table together and set in to 101.

Size: 4 Byte, Default Value: 0

Setting Description
1 Report Total HEM - KWH
2 Report Total HEM - Watt
4 Report Total HEM - Voltage
8 Report Total HEM - Current
256 Report Watt for Clamp 1
2048 Report KWH for Clamp 1
65536 Report Voltage (V) for Clamp 1
524288 Report Current (A) for Clamp 1

Parameter 111: Setting an automatic report interval

Set the report intervall for Group 1
Size: 4 Byte, Default Value: 0

Setting Description
1 - 2097152 seconds

Parameter 200: Partner ID


Size: 1 Byte, Default Value: 0

Setting Description
0 Aeon Labs Standard Product
1 others

Parameter 252: Enable/disable Configuration Locked


Size: 1 Byte, Default Value: 0

Setting Description
0 disable
1 enable

Parameter 255: Factory Reset


Size: 4 Byte, Default Value: 0

Setting Description
1 Reset to factory default setting
1431655765 Reset to factory default setting and removed from the zwave network

Technical Data

Dimensions 161x147x40 mm
Weight 370 gr
Hardware Platform ZM5202
EAN 1220000015777
IP Class IP 44
Voltage 230V
Load 200 A
Device Type Smart Meter
Firmware Version 1.21
Z-Wave Version 03.5c
Certification ID ZC10-15120010
Z-Wave Product Id 0x0086.0x0002.0x005f
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeSmart Meter