Aeon Labs
Home Energy Meter (C3 100A)
SKU: AEOEZW095C3A100
Quickstart
This is a
- Push the button on backside
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Installed in an electricity box, the energy meter will monitor the total consumption of electricity used by an entire building. And its intelligent clamps will report that energy use back to your Z-Wave gateway or controller, in watts or kilowatt-hours, and in real time. So you can see how much electricity you really use and when you use it.
Installation
Unless otherwise stated, the circuit box?s main breaker should be turned off to perform these installation steps.
- Turn the main breaker off.
- Open the main circuit box panel.
- Clip one clamp of the meter around the incoming electricity cable that connects to the main circuit breaker.
- Connect the clamp to the meter using a Clamp Connector.
- Connect the AC Wire to the meter using the AC Wire Connector.
- Wire the AC Wire into one breaker. The brown wire is Live, the blue wire is neutral.
- Replace the main circuit box panel.
- Turn the main breaker back on.
It is now time to place the main body of the Home Energy Meter. Inside the meter is a radio antenna used for communications, and this must be taken into consideration when selecting a location for the meter.
If the circuit boxes is made of metal the radio signal strength may be reduced. In this situation it is recommended that the main body of the meter be affixed outside the circuit box. This will improve the radio signal strength. The Home Energy Meter has been weatherized to the international IP43 standard so that it is resistant to rain and snow when placed vertically with the wires protruding from the bottom of the unit.
To place the Home Energy Meter:
- Unslot the backing plate from the back of your meter.
- Affix the plate to the selected wall space using the provided screws.
- Attach your meter to the backing plate.
Product Usage
Setting Parameter 101 -103
| Reset to factory default | - Press and hold the button on the backside for 10 seconds |
| Inclusion | - Push the button on backside |
| Exclusion | - Push the button on backside |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Send configured Value to devices |
| 2 | 5 | Send configured Value to devices |
| 3 | 5 | Send configured Value to devices |
Configuration Parameters
Parameter 2: Energy detection mode
For parameters of 101, power, energy detection mode Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | report power, energy absolute value |
| 1 | report positive/negative power, report the algebraic sum energy |
| 2 | report positive/negative power, only report energy positive part (consuming electricity) |
| 3 | report positive/negative power, only report energy negative part (generating electricity) |
Parameter 3: Selective reporting
Enable selective reporting only when power change reaches a certain threshold or percentage set in 4-11 below. This is used to reduce network traffic. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | disable |
| 1 | enable |
Parameter 4: Threshold change in wattage
Threshold change in wattage to induce a automatic report (Whole HEM). Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 0 - 60000 | Watt |
Parameter 5: Threshold change in wattage (Clamp 1)
Threshold change in wattage to induce a automatic report Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 0 - 100 | Valid value |
Parameter 6: Threshold change in wattage (Clamp 2)
Threshold change in wattage to induce a automatic report Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 0 - 100 | Valid value |
Parameter 7: Threshold change in wattage (Clamp 3)
Threshold change in wattage to induce a automatic report Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 0 - 100 | Valid value |
Parameter 8: Percentage change in wattage (Whole HEM)
Percentage change in wattage to induce a automatic report Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|
Parameter 9: Percentage change in wattage (Clamp 1)
Percentage change in wattage to induce a automatic report Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 100 | Valid value |
Parameter 10: Percentage change in wattage (Clamp 2)
Percentage change in wattage to induce a automatic report Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 100 | Valid value |
Parameter 11: Percentage change in wattage (Clamp 3)
Percentage change in wattage to induce a automatic report Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 100 | Valid value |
Parameter 13: Enable /disable reporting
Enable /disable reporting CRC-16 Encapsulation Command Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | disable |
| 1 | enable |
Parameter 100: Reset parameter 101-103
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | reset parameter 101-103 |
Parameter 101: Setting automatic report flags Group 1
Example: 1 + 1024 = Value 1025 If you want to report everthing, you would add the whole table together and set in to 101.
Please, see table in usage.
Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Report Total HEM - KWH |
| 2 | Report Total HEM - Watt |
| 4 | Report Total HEM - Voltage |
| 8 | Report Total HEM - Current |
Parameter 102: Setting automatic report flags Group 2
Example: 1 + 1024 = Value 1025 If you want to report everthing, you would add the whole table together and set in to 102.
Please, see table in usage.
Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Report Total HEM - KWH |
| 2 | Report Total HEM - Watt |
| 4 | Report Total HEM - Voltage |
| 8 | Report Total HEM - Current |
Parameter 103: Setting automatic report flags Group 3
Example: 1 + 1024 = Value 1025 If you want to report everthing, you would add the whole table together and set in to 103.
Please, see table in usage.
Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Report Total HEM - KWH |
| 2 | Report Total HEM - Watt |
| 4 | Report Total HEM - Voltage |
| 8 | Report Total HEM - Current |
Parameter 110: Reset parameter 111-113
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | reset parameter 111-113 |
Parameter 111: Setting an automatic report interval
Set the report intervall for Group 1 Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 - 2097152 | seconds |
Parameter 112: Setting an automatic report interval
Set the report intervall for Group 1 Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 - 2097152 | seconds |
Parameter 113: Setting an automatic report interval
Set the report intervall for Group 1 Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 - 2097152 | seconds |
Parameter 200: Partner ID
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Aeon Labs Standard Product |
| 1 | others |
Parameter 252: Enable/disable Configuration Locked
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | disable |
| 1 | enable |
Parameter 255: Factory Reset
Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Reset to factory default setting |
| 1431655765 | Reset to factory default setting and removed from the zwave network |
Technical Data
| Dimensions | 0.0960000x0.0700000x0.2300000 mm |
| Weight | 578 gr |
| Hardware Platform | ZM5202 |
| EAN | 1220000015616 |
| IP Class | IP 44 |
| Voltage | 400V |
| Load | 100A |
| Device Type | Smart Meter |
| Firmware Version | 01.02 |
| Z-Wave Version | 4.22 |
| Certification ID | ZC10-16105288 |
| Z-Wave Product Id | 0x0086.0x0002.0x005f |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |