This is a
Aeotec LED Bulb is a low-cost Z-Wave LED module which allows control (on/off/dim) with the use of Z-Wave.
Itâ??s a bulb has a Smart RGB LED, which can be used to add colour to your home. The bulb has 5 main colour channels available for you to adjust: Red, Green, Blue, Warm White and Cold White. You can configure its colour according to your favour.
The LED Bulb is also a security Z-wave device and supports the Over The Air (OTA) feature for the productâ??s firmware upgrade.
Reset to factory default | Turn the controller of Z-Wave network into exclusion mode, press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times. After the LED Bulb is excluded from network, it will be reset to factory default state. Use this procedure only in the event that your primary network controller is missing or inoperable. |
Inclusion | 1. Install the device according to the instructions. 2. Switch ON the bulb. 3. Swich OFF and On the bulb 3 times. |
Exclusion | 1. Turn on the Bulb.
2. Switch the Bulb off and on 3 times in a row. |
NIF | XXXNIF |
Wakeup | N/A |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Group 1 is assigned to the Lifeline association group and every device has 5 nodes to associate.When the Bulb is turned on or off using the external switch, the Bulb will send a basic report of its status to the nodes in association group 1. To change what kind of signal is sent to the nodes in group 1, please see the detailed description of configuration parameter 80. |
2 | 5 | When the product receives a controlling Basic Set CC/Switch Binary Set CC/Switch Multilevel Start Level Change CC, Switch Multilevel Stop Level Change CC, Switch Multilevel Set CC, Scene Activation Set CC, which if cause the productu2019s state to be changed, which will lead to send the Basic Set CC/Switch Binary Set CC to nodes in group 2. |
This parameter is used to enable/disable the function of using external switch to turn on/off the bulb. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
This parameter is used to enable/disable the function of using external switch to turn on/off the bulbs color. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
This parameter is used to Enable/Disable to send notifications to associated devices (in Group 1) when the state of bulb is changed. (0=Send nothing, 1=Send hail CC, 2=Send basic report CC). Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Send Nothing (Disabled) |
1 | Send HAIL Command |
2 | Send BASIC Report Command |
This parameter is used to configure the partner ID. (0== Aeon Labs Standard Product, 1~255== others). Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Aeon Labs Standard Product |
1 - 255 | Partner ID of Partner Product |
This parameter is used to enable/disable Lock all configuration parameters.(0 =disable, 1 = enable) Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | All configuration parameters are configurable. |
1 | All configuration parameters are not configurable (Locked). |
This parameter is used to reset product to default factory setting. (There are just 2 values can be used). Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1 | Reset all configuration parameters to default setting. |
1431655765 | Reset the product to default factory setting and be excluded from the Z-wave network. |
Dimensions | 0.0600000x0.1060000x0.0500000 mm |
Weight | 243 gr |
Hardware Platform | ZM5101 |
EAN | 1220000012974 |
IP Class | IP 20 |
Voltage | 230V |
Load | 9W |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Z-Wave Version | 6.51.06 |
Certification ID | ZC10-16065126 |
Z-Wave Product Id | 0x0086.0x0003.0x0062 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |