Aeon Labs

Door/ Window Sensor Gen5

SKU: AEOEZW120

ZWave+

Quickstart

This is a Notification Sensor for XXXQFrequencyName. To run this device please insert fresh 2 * AAA LR3 batteries. To run this device please make sure the internal battery is fully charged. Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action Button that you can find in the back of the product.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Aeon Labs Door/ Window Sensor  Gen5 is a smart Z-Wave sensor that can detect the status of door/window‘s open/close in real time.
It‘s a security Z-Wave device that supports security encryption. Also it supports over the Air Firmware Updating, that allows you wirelessly update its firmware if needs.
It can be included and operated in any Z-Wave network with other Z-Wave certified devices from manufacturers and/or other applications.

Installation

The installation of your Door Window Sensor has two major steps: the Main Sensor and the Magnet. Your Door Window Sensor will use wireless technology to talk to your Z-Wave network once paired to your Z-Wave network.
Selecting where you‘ll place your Door/Window Sensor in your home is just as important as the actual affixing it to the surface.

Whether it?s for security or intelligence purposes, your sensor:
1. Should be affixed indoors and away from sources of moisture.
2. Placed within 30 meters of another Z-Wave device that is either a gateway or not powered by batteries.
3. The magnet and the main sensor must be less than 2cm apart. Main sensor must be affixed to the door or window and the magnet must be affixed to the frame. The magnet and the main sensor must separate when the door or window is opened.
4. Should not be mounted on a metal frame.

Affix your Sensor plates to a surface.
The Mounting plates can be affixed using screws or double-sided tape.
If you are using screws, attach both mounting plates to the respective surface using the two 20mm screws provided.

If you are using double-sided tape, wipe the two surfaces clean of any oil or dust with a damp towel. When the surface has completely dried, peel one side of the tape back and attach it to the corresponding section on the rear side of the mounting plates.

Product Usage

img/AEO/AEOEZW120/Manual_Sketches_3.png
Reset to factory default Press the Action Button once that you can find in back of the product for 20 seconds and then release.
Inclusion 1. Open the housing. 
2. Remove the battery protection.
3. Press the button on the device once.
Exclusion 1. Open the housing .
2. Press the button in the device once.
NIF Press and hold the Action Button on the back of the Sensor unit for 3 seconds
Wakeup Press the Action Button once, which will trigger sending out the Wake up notification command, press and hold the Action Button for 3 seconds, which will toggle on/off the Sensor be waked up for 10 minutes.
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Lifeline

Configuration Parameters

Parameter 1: Value Type (Sensor Binary)

Which value of the Sensor Binary Report will be sent when the door is open/close.
Size: 1 Byte, Default Value: 1

Setting Description
0 Close = Sensor Binary Report 255 (0xFF) Open = 0 (0x00)
1 Close = Sensor Binary Report 0 (0x00) Open = 255 (0xFF)

Parameter 2: WackUp

Enable7disable wakeup 10 minutes when repower on the sensor
Size: 1 Byte, Default Value: 1

Setting Description
0 disabel
1 enable

Parameter 3: Value Typ (Basic set)

Which value of the Basic Set will be sent when the door is open/close.
Size: 1 Byte, Default Value: 1

Setting Description
0 Close = Sensor Binary Report 255 (0xFF) Open = 0 (0x00)
1 Close = Sensor Binary Report 0 (0x00) Open = 255 (0xFF)

Parameter 39: Low Battery value

Set the low battery value
Size: 1 Byte, Default Value: 10

Setting Description
10 - 50 in %

Parameter 111: Battery interval report

Note: 1, if the value is less than 10, the time unit is second. If the value is more than 10, the time unit is 4 minutes, which means if the value is more than 10 and less than 240, the interval time is 4 minutes. If the value is more than 240 and less than 480, the interval is 8 minutes. 2, if the current battery report falls below the low battery value (configurable parameter 39), it will send battery report=0xFF.
Size: 4 Byte, Default Value: 0

Setting Description
0 Disable the battery report for an interval time
1 - 2147483647 The interval time of battery report.

Parameter 121: Sensor report

To configure which sensor report will be sent when the Sensor is triggered On/Off.
Size: 4 Byte, Default Value: 256

Setting Description
16 Sensor Binary
256 Basic Set

Parameter 255: Factory Reset


Size: 4 Byte, Default Value: 0

Setting Description
1 Reset Parameters
1431655765 Facory Reset

Technical Data

Dimensions 39x79x22 mm
Weight 51 gr
Hardware Platform ZM5101
EAN 1220000013360
IP Class IP 20
Battery Type 2 * AAA LR3
Device Type Notification Sensor
Network Operation Reporting Sleeping Slave
Firmware Version 01.05
Z-Wave Version 04.05
Certification ID ZC10-16010006
Z-Wave Product Id 0x0086.0x0002.0x0078
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeNotification Sensor