Quickstart

This is a secure Light Dimmer Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. Turn the primary controller of Z-Wave network into inclusion mode, press the Action Button on the LED Strip Controller.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Aeotec LED Strip is a multi-coloured LED Strip which allows control (on/off/dim/colour change) via wireless Z-Wave commands. The LED Strip can also communicate securely via AES 128 wireless Z-Wave commands and supports Over-The-Air (OTA) firmware upgrades.

Installation



The installation of your LED Strip has two major steps: 
the LED  Strip Controller and the LED Strip. 

LED Strip can be installed inside or outside your home, but the LED Strip Controller should only be installed inside your home and should not be installed outdoor.

1. Plug the LED strip to the LED strip connector of your LED Strip Controller.
2. Connect the Power Adapter to your LED Strip.
3. Plug the Adapter into an electrical outlet and then the Network LED on LED Strip Controller will blink slowly to indicate it is ready to be paired to your Z-Wave network.
4. Now press the Action Button to toggle your LED strip on or off to ensure the connections between your LED Strip and its Controller roperly connected.

Reset to factory default Press and hold the Action Button on the LED Strip Controller for 20 seconds and then release it.
Inclusion Press the Action Button on the LED Strip Controller.
Exclusion Press the Action Button on the LED Strip Controller.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 The association group 1 is the Z-Wave Lifeline group. The Hail CC and Basic Report CC (configurable) can be sent to the associated nodes in association group 1.
2 5 In this group, the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands would be sent to the associated nodes in association group 2 when the LED Strip receives the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands from the main controller.

Configuration Parameters

Parameter 20: Set the LED Strips state after it is re-powered on

Set the LED Strips state after it is re-powered on.
Size: 1 Byte, Default Value: 1

Setting Description
0 The last state before re-power on.
1 Always On.
2 Always Off.

Parameter 32: Enable/disable to send out a report when the color is changed.

Enable/disable to send out a report when the color is changed.
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable
1 Hail CC

Parameter 33: Get the LED strips color value.

Get the  LED strips color value.Note: This parameter is a get-only parameter.
Size: 4 Byte, Default Value: 0

Setting Description
1 - 255 Blue color value
256 - 65535 Green color value
65536 - 16777215 Red color value

Parameter 34: Enable/disable to turn on the last brightness level of the LED Strip when using the Color Switch Set CC to change its color.

Enable/disable to turn on the last brightness level of the LED Strip when using the Color Switch Set CC to change its color.
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable
1 Enable

Parameter 35: Configure the display mode of Cold/Warm white.

Configure the display mode of Cold/Warm white.
Size: 1 Byte, Default Value: 1

Setting Description
0 Arbitrary combination of Cold/Warm white.
1 Complementary combination of Cold/Warm white.

Parameter 36: Reboot/save/exit Colorful mode.

Reboot/save/exit Colorful mode.Note: This parameter is a set-only parameter.
Size: 1 Byte, Default Value: 0

Setting Description
0 Un-reboot Colorful mode.
1 Reboot Colorful mode.
2 Exit Colorful mode.
3 Save the current Colorful mode value and then to be exited.

Parameter 37: Colorful mode configuration.

For advanced configuration, pleas read the manufactorer manual
Size: 4 Byte, Default Value: 157483008

Setting Description
0 - 31 Colour Change Speed Level
32 - 255 Time Base of Color Change Speed
256 - 65535 Cycle Count
65536 - 16777215 Brightness
16777215 - 134217727 Color Display Cycle
134217728 - 1073741823 Color Change Speed Option
1073741824 - 2147483647 Color Transition Style

Parameter 38: Change speed

Set the Change speed.
Size: 4 Byte, Default Value: 50332416

Setting Description
1 - 255 Set the pause time of OFF.
256 - 65535 Set the pause time of ON.
65536 - 16777215 Set the speed from ON to OFF.
16777216 - 2147483647 Set the speed from OFF to ON.

Parameter 39: Color index configuration when the LED Strip is in Multi color mode.

Color index configuration when the LED Strip is in Multi color mode.
Size: 4 Byte, Default Value: 2003125025

Setting Description
1 - 15 Index 8
16 - 255 Index 7
256 - 4095 Index 6
4096 - 65535 Index 5
65536 - 1048575 Index 4
1048576 - 16777215 Index 3
16777216 - 268435455 Index 2
268435456 - 2147483647 Index 1

Parameter 40: Colorful mode configuration.

Colorful mode configuration.
Size: 1 Byte, Default Value: 0

Setting Description
1 Rainbow mode.
2 Mutil color mode.
3 Fade out and fade in (Red).
4 Fade out and fade in (Green).
5 Fade out and fade in (Blue).

Parameter 80: To set whcih notification can be sent to the associated devices (Group 1) when the state of LED Bulb is changed.

To set whcih notification can be sent to the associated devices (Group 1) when the state of LED Bulb is changed.
Size: 1 Byte, Default Value: 1

Setting Description
0 Nothing
1 Hail CC
2 Basic CC report.
3 Haill CC when pressing the Action Button to change its state

Parameter 112: Set the Dimmer mode.

Set the Dimmer mode.
Size: 1 Byte, Default Value: 0

Setting Description
0 Parabolic curve mode
1 Index curve mode
2 (Parabolic + Index)/2 mode
3 Linear mode

Parameter 252: Enable/disable Lock Configuration

Enable/disable to lock Configuration parameters.
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable
1 Enable

Parameter 255: Reset the LED Strip

Reset the LED Strip to factory default.
Size: 4 Byte, Default Value: 0

Setting Description
0 Reset all configuration parameters to factory default settings
1431655765 Reset the LED Strip to factory default.

Technical Data

Dimensions 96 x 70 x 17,5 mm
Weight 536 gr
Hardware Platform ZM5101
EAN 1220000016002
IP Class IP 20
Voltage 24V
Load 3A
Device Type Light Dimmer Switch
Network Operation Always On Slave
Z-Wave Version 6.51.08
Certification ID ZC10-16095245
Z-Wave Product Id 0x0086.0x0003.0x0079
Color White
Z-Wave Scene Type Scene
Switch Type Push Button Illuminated
Firmware Updatable Updatable by Consumer by RF
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeLight Dimmer Switch