Quickstart

This is a WallMote for XXXQFrequencyName. To run this device please insert fresh * Rechargable batteries. To run this device please make sure the internal battery is fully charged.

1. Let your Z-Wave primary controller/gateway enter into pairing/inclusion mode.
2. Take your WallMote near to your primary controller. Press the Action Button once on your WallMote, the LED will blink with green color.
3. If your WallMote has been successfully added to your Z-Wave network, its green LED will be solid for 2 seconds and then off. If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.


Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Aeotec WallMote is an intelligent Z-Wave remote controller that mounted on a wall. It has 2 touch buttons that you can easily control the Z-Wave devices in your home network via touching, long pressing or sliding the button areas. Its surface has a RGB LED to indicate the button actions also accompanied by touch beep and vibration. The WallMote is also a security Z-Wave device and supports Over The Air (OTA) feature for the products firmware upgrade.

Product Usage

Dimmer control via sliding the button area.

The WallMote also supports sliding control, when the parameter 4 is set to 3, you can slide up or down on the button area to control the dimmer device.



Your WallMote battery.

Your WallMote has a internal rechargeable lithium battery that will allow you to charge it when it is in low battery. The charger?s output should be a micro USB terminal with the specification of output DC 5V/1A. When the WallMote is in charge state, the orange LED will be on. If the orange LED is off and the green LED remains on, then it indicates that the battery charge is complete. 
Note: When the WallMote is in low battery, you will see the orange LED will blink when you touch the control buttons. Otherwise, if the blue LED blinks when touching the buttons, which means the battery is in normal level.

Reset to factory default Press and hold the Action button (20 seconds). The LED should blink between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset. Let go of the Action Button.
Inclusion 1. Press the Action Button on your WallMote twice.
Exclusion 1. Press the Action Button on your WallMote once.
NIF Press Action Button
Wakeup Remove your WallMote unit from its Back Mounting Plate, press and hold the Action Button for 3 seconds(the buzzer chirp once and the orange LED will be ON) on the back of the WallMote unit and then release it. This will trigger and send a wake up notification command to your controller/gateway, then your WallMote will wake up for 10 minutes and the orange LED will fast blink while it is awake (if the WallMote does not receive the Wake Up No More Info from the primary Controller).
Protection XXXProtection
FirmwareUpdate The WallMote Quad is also a security Z-Wave device and supports Over The Air (OTA) feature for the products firmware upgrade.
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Lifeline - Central Scene control via Button 1 - 4
2 5 On/Off conrtol via Button 1
3 5 Dimmer control via Button 1
4 5 On/Off conrtol via Button 2
5 5 Dimmer control via Button 2

Configuration Parameters

Parameter 1: Touch Sound

Enable/disable the touch sound
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable
1 Enable

Parameter 2: Touch Vibration

Enable/disable the touch vibration
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable
1 Enable

Parameter 3: Button Slide

Enable/disable the function of button slide
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable
1 Enable

Parameter 4: Report

To configure which report will be sent when pressing the buttons.
Size: 1 Byte, Default Value: 1

Setting Description
1 Send Central Scene Command Notfication
3 Send Central Scene Command Notification an Configuration report

Parameter 39: Battery Level

Set the low battery value
Size: 1 Byte, Default Value: 5

Setting Description
5 - 50 Low battery value 5% -50%

Parameter 255: Factory Reset


Size: 4 Byte, Default Value: 1

Setting Description
0 Reset to factory setting (Size 1)
1431655765 Reset to factory default setting and removed from the Z-Wave network (Size 4)

Technical Data

Dimensions 76 x 76 x 10 mm
Weight 70 gr
EAN 1220000014428
IP Class IP 20
Voltage 3,7 V
Battery Type * Rechargable
Device Type WallMote
Firmware Version 01.05
Z-Wave Version 04.21
Certification ID ZC10-17025441
Z-Wave Product Id 0x0086.0x0002.0x0081
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeWallMote