Quickstart

This is a secure Thermostat - HVAC for XXXQFrequencyName. To run this device please insert fresh 2 * AA LR6 batteries. To run this device please make sure the internal battery is fully charged.

- Start Inclusion mode of your primary Z-Wave Controller.

- Press the Boost-Button.

- Aeotec Radiator Thermostat will show the assigned NodeID.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Aeotec Radiator Thermostat is a Z-Wave radio standard compatible energy-saving radiator thermostat for Europe.

Installation

Mounting the Aeotec Radiator Thermostat

After adding the Aeotec Radiator Thermostat to a network it is ready to be installed on the radiator. The LCD shows INS. Do not press the boost button yet.

Installation at the radiator without Adapter

Installation at the radiator with Adapter

Mechanical Installation

Press the boost button to start mechanical installation.

Unmounting the Aeotec Radiator Thermostats

Product Usage

Buttons:

Boost-Taste Led‘s

LCD

Inserting batteries

Remove the battery cover by simply pulling it off. Now insert the batteries. Pay attention to the correct

polarity! At a later battery change, the configuration of your Aeotec Radiator Thermostat is maintained.

Setpoint adjustment

The setpoint is adjusted via plus and minus button.

Altering the setpoint locally will set the Aeotec Radiator Thermostat in heating mode.

The energy saving setpoint can only be adjusted via Z-Wave.

The configurable setpoint range is 8°C to 28°C.

If the setpoint is increased/decreased above/below the set point limits, the

Aeotec Radiator Thermostat will change into boost / off mode.

Child protection

Press and hold plus and minus button simultaneously for 3 seconds to enable/disable the child protection.

If the Aeotec Radiator Thermostat is set into the highest protection level it is no longer possible to operate the device locally.

Altering the operating states

Off-Mode

Press minus button until OFF is displayed.

Boost-Mode

Push the boost button.

Alternatively, press the plus button until ON is displayed.

Heating-Mode

If the operating state is not heating mode, pressing the plus or

minus button will bring the device in heating mode.

Window open detection

If the room temperature drops, the window open detection will trigger.

Aeotec Radiator Thermostat will change temporarily in off mode for 15 minutes.

Window open detection will end automatically after 15 minutes and the previously active

operating mode will be restored.

Window open detection can also be canceled by a button press.

The window open detection is disabled during manufacturer-specific mode.

The sensitivity of the window open detection can be configured

Display NodeID

Press and hold the boost button for 3 seconds to display the NodeID.

Reset to factory default	1. Remove batteries. 2. Press and hold boost button. 3. While still holding boost button insert batteries. 4. The LCD shows RES. Release boost button. 5. To perform the factory reset press boost button.
Inclusion	1. Insert the batteries 2. Press the Boost-Button once.
Exclusion	1. Press and hold the boost button of the Radiator Thermostat for at least 5 seconds.
NIF	XXXNIF
Wakeup	XXXWakeupDescription
Protection	XXXProtection
FirmwareUpdate	XXXFirmwareUpdate
SetAssociation	XXXSetAssociation

Association Groups:

Group Number	Maximum Nodes	Description
1	1	Z-Wave Plus Lifeline

Configuration Parameters

Parameter 1: LCD invert

Inverts the LCD orientation
Size: 1 Byte, Default Value: 0

Setting Description
0 Normal orientation

1 LCD content inverted

Setting	Description
0	Normal orientation
1	LCD content inverted

Parameter 2: LCD Timeout

Configures the timeout of the LCD.
Size: 1 Byte, Default Value: 0

Setting Description
0 LCD always on

5 - 30 LCD timeout in seconds

Setting	Description
0	LCD always on
5 - 30	LCD timeout in seconds

Parameter 3: Backlight

Enables or disables the LCD-Backlight.
Size: 1 Byte, Default Value: 1

Setting Description
0 Backlight disabled

1 Backlight enabled

Setting	Description
0	Backlight disabled
1	Backlight enabled

Parameter 4: Battery report

Enables or disables unsolicited battery reporting once a day.
Size: 1 Byte, Default Value: 1

Setting Description
0 Battery reporting disabled

1 Battery reporting enabled

Setting	Description
0	Battery reporting disabled
1	Battery reporting enabled

Parameter 5: Measured temperature report

Reports the measured roomtemperature on change.
Size: 1 Byte, Default Value: 5

Setting Description
0 Reporting disabled

1 - 50 Reporting Delta in 1/10 Celcius

Setting	Description
0	Reporting disabled
1 - 50	Reporting Delta in 1/10 Celcius

Parameter 6: Valve percentage report

Reports the valve percentage on change.
Size: 1 Byte, Default Value: 0

Setting Description
0 Reporting disabled

1 - 100 Reporting Delta in percent

Setting	Description
0	Reporting disabled
1 - 100	Reporting Delta in percent

Parameter 7: Window open detection

Configures the sensitivity of the window open detection.Sensitivity level: 1 low2 medium3 high
Size: 1 Byte, Default Value: 2

Setting Description
0 Detection disabled

1 - 3 Sensitivity level

Setting	Description
0	Detection disabled
1 - 3	Sensitivity level

Parameter 8: Measured temperature offset

Configures an offset for the measured temperature. Set the offset to -128 (0x80) if measured temperature is provided externally.
Size: 1 Byte, Default Value: 0

Setting Description
0 - 50 Offset in 1/10 Celcius (0°C - 5°C)

128 Temperature is supplied externaly

206 - 255 Offset in 1/10 Celcius (-5°C - 0,1°C)

Setting	Description
0 - 50	Offset in 1/10 Celcius (0°C - 5°C)
128	Temperature is supplied externaly
206 - 255	Offset in 1/10 Celcius (-5°C - 0,1°C)

Technical Data

Dimensions	55 x 67x 67 mm
Weight	127 gr
Hardware Platform	ZM5202
EAN	4251295701387
IP Class	IP 20
Voltage	3V
Battery Type	2 * AA LR6
Device Type	Thermostat - HVAC
Network Operation	Listening Sleeping Slave
Z-Wave Version	6.71.01
Certification ID	ZC10-20076945
Z-Wave Product Id	0x0371.0x0002.0x0015
Firmware Updatable	Updatable by Consumer by RF
Sensors	Air Temperature
Supported Notification Types	Power ManagementSystem
Thermostat HVAC Systems Supported	Heat Only
Thermostat Modes	Energy Save HeatHeat
Frequency	Europe - 868,4 Mhz
Maximum transmission power	5 mW

Aeotec

Radiator Thermostat

SKU: AEOEZWA021