Aeotec
Z-Wave Multisensor
SKU: AEORZW100
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Motion sensor.
Motion for security. Motion for presence. Motion for management. MultiSensor 6&rsquos motion sensor is perfect for more than just an intelligent security system. With a 5 metre range and a 120° field of view, MultiSensor 6 captures motion data that can be used for everything from security to heating management to energy saving. Knowing if a room is occupied or a hall is being used is a powerful piece of data – MultiSensor 6 makes your home automation system more powerful and more intelligent.
Temperature sensor.
From motorised curtains and windows to fans and thermostats, there are a lot of ways that you can use Z-Wave to keep the temperature of a room absolutely perfect. MultiSensor 6 provides the intelligence to do just that. Within each sensor is an incremental temperature sensor capable of accurately measuring between -10~50°C (14 to 122°F) and reporting temperature changes back to a smart home gateway.
Light sensor.
Automated lighting is only as smart as the system that powers it. With MultiSensor 6&rsquos real-time, digital light sensor measuring the level of light in a room, your home control system will be able to intelligently maintain its ambiance. From opening and closing curtains, to setting lights to be the perfect level be it day or night, MultiSensor 6 is the smarts behind smart lighting.
Humidity sensor.
Spaces such as bathrooms and kitchens can be too humid, while some environments are often not humid enough. MultiSensor 6 offers incremental monitoring of a humidity ranging from 0% to 100%, allowing for the intelligent automation of fans, motorised windows, dehumidifiers and humidifiers. MultiSensor 6 monitors your home on such an infinitesimal level so that your home management system can make your environment truly perfect.
Vibration sensor.
It measures the environement it&rsquos in, and it also measures itself. MultiSensor 6 contains a seismic sensor capable of detecting and reporting event-based vibrations. Those slight changes can be used to protect MultiSensor 6 – it&rsquoll know if an intruder is tampering with it or if the sensor has accidentally moved from its place of installation. They&rsquoll also be able to record subtle seismic activity within your home.
UV sensor.
Perfectly managing an environment means understanding it perfectly. MultiSensor 6 accurately measures ultraviolet light the kind of light that causes everything from furniture bleaching to eye damage. Measured inline with the World Health Organisation&rsquos UV Index, MultiSensor 6 measures a room&rsquos UV level so that an environment can be managed through curtains, shades and lighting, and so that health and property recommendations can be made.
Perfect power
Perfect battery life isn&rsquot perfect for every installation. For all those times, MultiSensor 6 can be run on mains power. Simply connect it to your home&rsquos electricity using the provided USB cable and MultiSensor 6 will be able to run in an advanced mode, providing temperature, humidity and light readings in real-time.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0000000x0.0000000x0.0000000 mm |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.