This is a
Single click the button located near the Status Indication LED or alternatively press the external switch/ button control quickly 6 times to include or exclude the device. If the Aeon Labs Micro Illuminator is not included into any Z-Wave network, the LED will be blinking slowly continually.
The Aeon Labs Micro Illuminator is a Z-Wave light dimmer specifically used to enable Z-Wave command and control (on/off/dim) for existing in-wall dimmers. The wireless module is powered from the mains supply and is a three-wire design which requires a neutral connection. In the event of power failure, non-volatile memory retains all programmed information relating to the units operating status.
The device is designed for a 3 wire system which requires a neutral connection. The module is powered from the main supply.
The schematic below shows how to wire the actuator. The power supply and the appliance are connected by the Load, Power Input and Neutral connectors. The 3.3 Volt and External Switch connectors are for external switching.
After the electrical installation the device has to be implemented in the Z-Wave Network.
The dimmer is operated by an external switch/button or wireless. The click on the switch sets the dimmer on or off. To have the dimming function simple hold the button pushed until your desired level. The dimmer insert memorizes the last lighting level and switches automatically to the same level.
Reset to factory default | XXXResetDescription |
Inclusion | To include the Aeon Labs Micro Illuminator with your Z-Wave controller simple bring it in the inclusion-mode and click the Inclusion/Exclusion button at the Aeon Labs Micro Illuminator once. Alternatively you can use the external switch by quickly pressing it six times. If the Aeon Labs Micro Illuminator was successfully included to a Z-Wave network, the Status Indication LED will either be solid on or off (depending on if the switch is on or off) 10 seconds after the button was last pressed. |
Exclusion | To include the Aeon Labs Micro Illuminator with your Z-Wave controller simple bring it in the inclusion-mode and click the Inclusion/Exclusion button at the Aeon Labs Micro Illuminator once. Alternatively you can use the external switch by quickly pressing it six times. If the Aeon Labs Micro Illuminator was successfully included to a Z-Wave network, the Status Indication LED will either be solid on or off (depending on if the switch is on or off) 10 seconds after the button was last pressed. |
NIF | A single click at the Inclusion/Exclusion switch sends a Node Information Frame. |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Status Reports |
Defines the value type to be sent as Sensor Report. Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Power |
01 | Voltage |
This is a double byte value. The LSB defines the total time the device need to blink. The value if set in seconds. The MSB defines the on/off interval of the blinking. The unit is 0.1 s. Size: 2 Byte, Default Value: 0000
Setting | Description |
---|
Defines the automated status notification of an associated device when status changes Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Deactivated |
01 | Hail sent |
02 | BASIC Report Sent |
Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Disabled |
01 | Enabled |
The value represents the minimum change in Wattage for a Report to be sent . Size: 2 Byte, Default Value: 0032
Setting | Description |
---|---|
00 - 3500 | Value in Watt |
The value represents the minimum change in Wattage Percent for a report to be sent Size: 1 Byte, Default Value: 0a
Setting | Description |
---|---|
00 - 100 | Percentage |
Defines the type of report sent for the Reporting Group 1. Size: 4 Byte, Default Value: 00000008
Setting | Description |
---|---|
Byte 1: 00000100 | MultiSensor Report |
Byte 1: 00001000 | Meter Report for Watt |
Byte 1: 00010000 | Meter Report for kWh |
Defines the type of report sent for the Reporting Group 2. Size: 4 Byte, Default Value: 00000000
Setting | Description |
---|---|
Byte 1: 00000100 | MultiSensor Report |
Byte 1: 00001000 | Meter Report for Watt |
Byte 1: 00010000 | Meter Report for kWh |
Defines the type of report sent for the Reporting Group 3. Size: 4 Byte, Default Value: 00000000
Setting | Description |
---|---|
Byte 1: 00000100 | MultiSensor Report |
Byte 1: 00001000 | Meter Report for Watt |
Byte 1: 00010000 | Meter Report for kWh |
Defines the time interval when the defined report of Reporting Group 1 is sent out. Size: 4 Byte, Default Value: 000002d0
Setting | Description |
---|---|
00 - ffff | Seconds |
Defines the time interval when the defined report of Reporting Group 2 is sent out. Size: 4 Byte, Default Value: 000002d0
Setting | Description |
---|---|
00 - ffff | Seconds |
Defines the time interval when the defined report of Reporting Group 3 is sent out. Size: 4 Byte, Default Value: 0000ffff
Setting | Description |
---|---|
00 - ffff | Seconds |
Dimensions | 0.0510000x0.0510000x0.0180000 mm |
Weight | 40 gr |
Hardware Platform | ZM3102 |
EAN | 1220000011489 |
IP Class | IP 20 |
Voltage | 230 |
Device Type | Light Dimmer Switch |
Generic Device Class | Multilevel Switch |
Specific Device Class | Routing Multilevel Switch |
Firmware Version | 01.18 |
Z-Wave Version | 02.4e |
Certification ID | ZC08-13030004 |
Z-Wave Product Id | 0086.0003.000d |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |